VEN T IL AT ION
DX Ceiling Fan Kit 50Hz/60Hz
Supply / Extract Units – Installation and Maintenance 1.0 Safety Information IMPORTANT: Installation or replacement of units or spare parts must be carried out by a qualified or Domus approved service engineer/ electrician and in accordance with IEE or local national wiring regulations. 2.0 Introduction
2.2 Sensors
The Domus DX Ceiling Fan Kit is available in 6, 9 and 12 inch impeller sizes suitable for supply or extract.
Sensors are available as remote units or integral ‘plug in’ units. They are able to control multiple fans, depending on sensor and fan types. Integral sensors are quick and easy to install and are aesthetically pleasing, whilst remote sensors give the benefit of location close to the pollutant source. Remote sensors can be fitted with an optional security strap to prevent unwanted tampering.
Ensure adequate air replacement for the fan and any fuel burning appliance in the room.
Figure 1.Main components of ceiling installation assembly.
2.3 General The removable interior grille provides easy access while the external rotor motor makes for simple removal of the push-on impeller for cleaning. Upward angled interior grille vanes shield workings from view. The fan is IP24 splash proof approved with the motor rated at IP44.
Internal Grille Mounting Brackets Duct Adaptor
Fan casing, impeller and shutter shall be manufactured from UV stabilised ABS polymer. All models shall include an economy /high efficiency setting facility and are dove grey in colour.
Mounting Screws
2.3.1 Coding For Ceiling Fan Kits
Fan assembly
Description
2.1 Switching Operated via a separately wired 3 amp fused spur (by others) or operated via the optional DX-CON remote controller allowing supply or extract, variable speed and automatic or manual switching of several fans if desired.
3.0 Dimensions
6 inch Ceiling Fan Kit Complete
DX6PL
9 inch Ceiling Fan Kit Complete
DX9PL
12 inch Ceiling Fan Kit Complete
DX12PL
Ceiling Fan Kits are supplied as a complete package with all installation parts included. DX6CL (6 in ch)
Figure 2. DX6CL (6 in ch)
DX6CL (6 in ch)
Front View
DX9CL (9 in ch)
Rear View
272mm
272mm
DX9PL (9 in ch)
DX6PL (6 in ch)
272mm
342mm
Required ceiling/panel aperture 270 x 270mm sq. Cable entry
*To centre of 'duct' 134 mm* 269 mm
Side view
200 mm*
128mm *Duct Adaptor
206 mm* 413mm 128mm 230 mm*
130mm
169 mm
420mm
Required ceiling/panel aperture 340 x 340mm sq. 420mm Cable entry Required ceiling/panel aperture 430 x 430mm sq. Cable entry
342mm
137 mm*
175mm*
Required ceiling/panel aperture 430 x 430mm sq. Cable entry
420mm
214 mm*
206 mm* 200 mm* 413mm
*To centre of 230 mm* 'duct'
200 mm* 130mm
200 mm*
230 mm*
130mm
169 mm
*To centre of 350 mm* 'duct'
250 mm*
350 mm*
250 mm* 337 mm *Duct Adaptor
*To centre of 'duct'
206 mm* 413mm
171mm* 337 mm*To centre of 'duct'
175mm*
200 mm*
214 mm*
Required ceiling/panel aperture *To centre of x 430mm sq. 430 214 mm* 'duct' Cable entry
171mm*
128mm
200 mm* *Duct Adaptor
420mm
342mm
342mm
200 mm* 171mm* 337 mm
269 mm
420mm
420mm
342mm
134 mm* 269 mm*To centre of 'duct'
'duct' 6 inch unit 200mm dia. 9 inch unit 250mm 134 mm* dia. *To centre of 12 inch 200 unit mm*350mm dia. 'duct'
Duct Adaptor Outlet dia.* 6250inch mm*unit 200mm dia. 9 inch unit 250mm dia. 12 inch unit 350mm dia.
200 mm*
137 mm*
DX12CL (12 inch)
342mm
Required ceiling/panel aperture centre of sq. 340*To x 340mm 175mm* 'duct' Cable entry
centre of 214 mm* Duct Adaptor Outlet *To dia.* 200 mm* 200 mm*
*To centre of
Duct Adaptor Outlet dia.* 'duct' 6 inch unit 200mm dia. 171mm* 9 inch unit 250mm dia. 337 mm12 inch unit 350mm dia.
Side view
200 mm*
tor Outlet dia.* 200mm dia. 250mm dia. t 350mm dia.
*To centre of Required ceiling/panel aperture 'duct' 430 x 430mm sq. Cable entry134 mm* 269 mm
Side view
DX12CL (12 inch)
Required ceiling/panel aperture 340 x 340mm sq. Cable entry
420mm
175mm*
137 mm*
e view
Required ceiling/panel aperture 270 x 270mm sq. 269mm Cable entry 420mm
DX12CL (12 inch)
DX9CL (9 in ch) 272mm
269mm
Required ceiling/panel aperture 270 137 x 270mm sq. mm* Cable entry
Required ceiling/panel aperture 340 x 340mm sq. Cable entry
DX9CL (9 in ch)
Required ceiling/panel aperture 270 x 270mm sq. 342mm Cable entry
DX12PL (12 inch) 269mm
342mm
269mm
Code (50 Hz)
206 mm* 413mm
169 mm
230 mm*
350 mm*
250 mm*
350 mm*
128mm
*Duct Adaptor
130mm
169 mm
Page 1
Installation and Maintenance DX Ceiling Fan Kit 50Hz/60Hz
V EN T IL AT ION
4.0 Installation 4.0 Installation 4.1 Installation4.1 OfInstallation Ceiling FanOf Kits Ceiling Fan Kits
1
2
1
Aperture
Aperture
6 inch fan
6 inch fan
270mm x 270mm
270mm x 270mm
9 inch fan
9 inch fan
340mm x 340mm
340mm x 340mm
12 inch fan 430mm x 430mm
12 inch fan 430mm x 430mm
2
Prepare the aperture Prepare to suit the the aperture fan size.to suit the fan size.
Cut and fit timber Cut supports and fit(not timber supplied) supports for aperture (not supplied) for aperture as shown. as shown.
3
4
4
Mounting Bracket with threaded insert
Mounting Bracket with threaded insert
3
Offer the duct adaptor Offerand the the ducttwo adaptor metaland brackets the two metal brackets into position. into position.
5
5
Lock the screw rods Lock with the the screw nutsrods provided. with the nuts provided.
7
7
Feed the supply cable Feedthrough the supply the cable duct adaptor. through the duct adaptor.
Screw theinto 2 mounting rodsfrom into the brackets below. from below. Screw the 2 mounting rods the brackets
6
6
Fix the metal brackets Fix the to the metal cross brackets battens. to the cross battens.
8
8
Offer the fan up into Offer thethe duct fan up into the duct adaptor and fix using adaptor the two andscrews. fix using the two screws.
Page 2
Installation and Maintenance DX Ceiling Fan Kit 50Hz/60Hz 9
9
Remove the electrical Remove connection the electrical panel (top connection left). panel (top left).
11
V EN T IL AT ION 10
10
Bring the cable through Bring the cable fan plate through approx the150mm. fan plate approx 150mm. See wiring page 4 for Seevarious wiring page wiring4 options. for various wiring options.
11
IMPORTANTIMPORTANT
Fix the electrical connection Fix the electrical before connection offering up before the internal offering up the internal grille. Note grille clips grille. over Note topgrille edgeclips before over being top edge fixed.before being fixed.
(Shutter Operation (Shutter XS fans) Operation XS fans) There will be a short There delay willon bestart-up a short delay and shutdown on start-up of and shutdown of approximately 40approximately seconds, this is40normal. seconds, this is normal.
Page 3
Installation and Maintenance DX Ceiling Fan Kit 50Hz/60Hz
V EN T IL AT ION
5.0 Electrical 5.0 Installation Electrical Installation Electrical work Electrical should be work undertaken should beby undertaken a qualifiedby electrician a qualified in electrician in accordance with accordance the wiring with regulations. the wiring regulations.
1
1
2
2
Release the electrical Release panel the electrical from the panel fan plate. from the fan plate.
Remove the terminal Remove cover. the terminal cover.
3
4
3
4
Refit terminal cover Refit before terminal replacing cover before the electrical replacingpanel. the electrical panel.
Clamp the cableClamp and complete the cablethe andconnections. complete the connections.
5.1 Wiring 5.1 Wiring 5.1.3 Basic Fan 5.1.3 Operated Basic Fan ByOperated Remote Sensor By Remote Sensor
5.1.1Fan Operated 5.1.1Fan ByOperated On / Off Switch By On / Off Switch L5 L4 L3 L2 L1 N
or
L
Double pole isolator L
N
N
Double Fuse pole isolator max. 3 amp
Fuse max. 3 amp
or
DX Fan unit
Remote Sensor Remote Sensor L1 L2 N L1 L2 N
L5 L4 L3 L2 L1 N
Double pole isolator
Fuse Double max. pole 3 ampisolator
Fuse max. 3 amp
L5 L4 or L3 L2 L1 N
or
XS Fan unit
XS Fan unit
L5 L4 L3 L2 L1 N DX Fan unit
Connect link wire Connect between link wire L2 &between L4 for extract L2 & L4 ORfor extract OR connect link wire connect between link wire L2 &between L3 for supply. L2 & L3 for supply.
Connect link wire Connect between link wire L2 &between L4 for extract L2 & L4 ORfor extract OR connect link wire connect between link wire L2 &between L3 for supply. L2 & L3 for supply.
5.1.2 Fan Operated 5.1.2 Fan ByOperated Integral Sensor By Integral Sensor SL SL (Swit ched Live) (Swit ched Live) or
L N
Double pole isolator L
Double Fuse pole isolator max. 3 amp
N
Fuse max. 3 amp
L5 L4 or L3 L2 L1 N
L5 L4 L3 L2 L1 N
IMPORTANT IMPORTANT Isolation - Before Isolation commencing - Beforework, commencing make sure work, thatmake the unit sureisthat the unit is electrically isolated electrically from the isolated mainsfrom supply. the mains supply.
DX Fan unit withXS Fan unit with integral sensor integral sensor
Connect link wire Connect between link wire L2 &between L4 for extract L2 & L4 ORfor extract OR connect link wire connect between link wire L2 &between L3 for supply. L2 & L3 for supply. Connect switched Connect live switched signal to L5 liveforsignal integral to L5 timer for integral module.timer module.
Page 4
Installation and Maintenance DX Ceiling Fan Kit 50Hz/60Hz
V EN T IL AT ION
& Weight 5.1.4 Fan Operated via via remote DX-CON Control 5.2Consumption Unit Consumption & Weight Supply/ /Extract Extract Fan Operated remote DX-CON Control5.2 Unit 5.1.4Supply
Double Double pole pole isolator
isolator
L
L
Fuse Fuse max. max. 3 amp
3 amp
N
N
L4 L3 L2 L1 L1 L1 N N
N
mains supply mains
L5 L4 L3 L2 L1 N
L4 L3 L2 L1 N
Input Power Input Power L5 Weight (W) Model Model (W) L4 (kg) L3 Max. Max. Economy Economy L2 DX6PL supply & extract 38 20 3.95 L1 DX6PL supply & extract 38 20 N DX9PL supply & extract 50 37 5.5
DX9PL supply & extract
DX12PL supply & extract
DX Fan unit
DX-CON cont roller
DX Fan unit
DX12PL supply & extract
100
50
100
70
supply DX-CON cont roller Extract, Economy/Std. Note figures are for extract only at 50hz. Remote switch may be set: On/Off, Supply/ Note figures are for extract only at 50hz. Remote switch may be set: On/Off, Forward/Reverse, Economy/Std. (variable speed), Auto/Manual.
37
70
8.7
Weight (kg) 3.95 5.5 8.7
5.3 Electrical Specification
(variable speed), Auto/Manual.
5.3 Electrical Specification
230V ~ 50Hz / 220V ~ 60Hz Class I. Motor thermally protected by 5.1.5 Supply / Extract Fan Operated via remote DX-CON Control device. Cable: 1mm~max. min.I.Fuse: 3 amp (if fan isprotected supplied by 230V ~ 50Hz / 220V 60HzorClass Motor thermally 5.1.5Remote SupplySensor / Extract Fan Operated via remote DX-CON Controloverload and from a 5A lighting circuit, no local fuse is required). overload device. Cable: 1mm max. or min. Fuse: 3 amp (if fan is supplied Remote sensor and Remote Sensor from a 5A lighting circuit, no local fuse is required). Note: If 2 x 12 inch fans or 3 x 6 or 9 inch fans are used in the same L2 L1 Remote N sensor L2 L1 N Double pole isolator
Double pole isolator
L N
L
Fuse max. 3 amp
Fuse max. 3 amp
N mains supply
L1 N
L5 L4 L3 L2 L1 N
L4 L3 L4 L2 L1 L3 N L2
L1 N
L1 N
DX Fan unit
operating mode samefans room all be controlled from Note: If 2inx the 12 inch orthey 5 x 6should or 9 inch fans are used in the same the same CON speed control. This avoids the possibility of one fan (if operating mode in the same room they should all be controlled from controlled at a lower flow rate) being stalled by the other fan(s). L5 speed the same DX-CON speed control. This avoids the possibility of one fan (if L4 Adequate make-up air provision sufficient to provide ventilation in speed controlled at a lower flow rate) being stalled by the other fan(s). L3 accordance with building regulations is required in all rooms. This make-up air provision sufficient to in provide ventilation L2 shouldAdequate be checked during commissioning with all fans the same room in L1 running accordance with building regulations is required in all rooms. This together in all possible configurations. N
should be checked during commissioning with all fans in the same room
The automatic bearings configurations. should be frequently inspected running shutters, togethermotor in all possible Remote switch may be set: On/Off, Supply/ Extract, Economy/Std. and maintained to ensure they open fully/operate satisfactorily. Use mains DX Fan unit supply (variable speed), Auto/Manual.DX-CON cont roller The and automatic shutters, motor bearings should be frequently inspected of an RCD fused spur with 1A, Bussmann TDC180, BS1362, fuse Remote switch may be set: On/Off, Forward/Reverse, Economy/Std. (Farnelland order no: 1123029) for 1 fan or 2A, Bussmann TDC180, BS1362 maintained to ensure they open fully/operate satisfactorily. Use One or more Remote Sensors may be wired in parallel to one DX-CON (variable speed), Auto/Manual. fuse (Farnell orderand no:fused 1123032) 2 or1A, 3 fans is recommended. of an RCD spurfor with Bussmann TDC180, BS1362, fuse Control. DX-CON cont roller
no: 1123029) for commissioning. 1 fan or 2A, Bussmann TDC180, BS1362 Humidity Sensor: DX-RHSensors may be wired in parallel to one DX-CONAlways(Farnell confirmorder airflow direction before One or more Remote fuse (Farnell order no: 1123032) for 2 or 3 fans is recommended.
Control. Humidity Sensor: DX-HR Air Quality Sensor: DX-AQR 5.1.6 Supply / Extract Fan Operated via remote DX-CON Control Passive Infra-Red Sensor: DX-PIRR and an Integral Sensor
Always confirm airflow direction before commissioning.
5.1.6 Supply / Extract Fan Operated via remote DX-CON Control Required if using integral Timer and an Integral Sensor Double pole isolator L N mains L supply
Double pole isolator
Fuse max. 3 amp
Fuse max. 3 amp
N
L1 N
L4 L3 L2 L1 L4 N
L3 L2 DX-CON cont L1 roller L1 N N
Required if using integral Timer
L5 L4 L3 L2 L1 N
DX Fan unit with integral sensor
L5 L4 L3 L2 L1 N
Remote switch may be set: On/Off, Supply/ Extract, Economy/Std. mains (variable speed), Auto/Manual. DX Fan unit with supply
DX-CON cont roller
integral sensor
Maximum one Integral Sensor per fan, 6/9/12 denotes unit size identity.
Remote switch be set: On/Off, Forward/Reverse, Economy/Std. Humidity Sensor: may DX-H6/9/12 (variable speed), Auto/Manual. Passive Infra Red Sensor: DX-PIR6/9/12 Run on Timer: DX-T6/9/12. Maximum one Integral Sensor per fan, 6/9/12 denotes unit size identity. A single sensor will switch all fans if more than one fan is being HumiditybySensor: operated a singleDX-H6/9/12 DX-CON controller.
Passive Infra Red Sensor: DX-PIR6/9/12
NOTE: options: Run onMulti-fan Timer: DX-TA6/9/12. Up to 5 fans (size 6"/9") can be controlled by one DX-CON. A single sensor fans if more than one fan is being Up to 2 fans (size will 12")switch can beall controlled by one DX-CON. operated a single Do not mix by different fanDX-CON sizes oncontroller. the same controller.
NOTE: Multi-fan options: Up to 5 fans (size 6"/9") can be controlled by one DX-CON. Up to 2 fans (size 12") can be controlled by one DX-CON. Do not mix different fan sizes on the same controller.
Page 5
Installation and Maintenance DX Ceiling Fan Kit 50Hz/ 60Hz 5.4 Fitting 5.4 Integral Fitting Integral SensorsSensors (Optional) (Optional)
V EN T IL AT ION 11
Note: Before Note:following Before following the pictorial the pictorial sequencesequence shown, first shown, remove first the remove the fans front fans cover front grille cover (2 screws). grille (2 screws). Release the Release four the main four corner mainscrews corner screws and lift out andthe liftmotor/fan out the motor/fan plate assembly. plate assembly. Remove Remove the electrical the electrical cover cover plate opposite plate opposite the sensor theplate. sensor Follow plate.the Follow pictorial the pictorial sequencesequence on this on this page. page.
11
Unscrew the Unscrew module theplate module fromplate motor from plate motor assembly. plate assembly.
2
2
Remove the Remove module theplate. module plate.
4
4
3
3
Lift out the Liftsensor out the module sensorwiring module connector. wiring connector.
5
5
Plug the connector Plug the connector into the required into thesensor required module. sensor module.
Screw theScrew sensorthe module sensorinto module position. into position.
6
7
6
Push out the Pushsensor out the area sensor coverarea fromcover the grille. from the grille.
LAB1345R (version 1) April 2018
7
Push the repacement Push the repacement cover intocover the grille into front. the grille front.
Page 6
Installation and Maintenance DX Ceiling Fan Kit 50Hz/ 60Hz DX-CONXS-MFC or 5.5 Fitting Fitting 5.5Remote Fitting Remote Controller Controller XS-MFC or or RemoteRemote Remote sensors sensors (optional) (optional)
V EN T IL AT ION 1
1
FanMulti Control provides supply or orsupply extract, variable and The DX-CON TheMulti DX-CON Fan Control Fanprovides Control supply provides extract, orvariable extract, speed variable automatic or manual switching of several switching fans if desired (see note speed andspeed automatic and automatic or manualor switching manual of several offans several if desir fans below) if desir note The control below). isThe best control mounted best approx mounted 1.5mmounted approx above1.5m the floor. above Remote theabove floor. Sensors are note below). Theiscontrol is best approx 1.5m the floor. Remote are available for Humidity, Aironly. Quality Passive Remote Sensors are available for Humidity, Airand Quality andInfra Passive availableSensors for Humidity (with run-on timer) Remote Sensors shouldInfra be Red control. Sensors should beshould positioned at least 1.5m above Red control. Remote Sensors be positioned at least 1.5m above positioned atRemote least 1.5m above the floor and away from direct heat sources e.g. the floor and awayand from direct heat sources radiators. the floor away from direct heate.g. sources e.g. radiators. radiators.
Note: Note: Note: Up to to 55 fans fans (size inch) be controlled controlled by one one DX-CON. DX-CON. Up (size 66 // 99(size inch) be by Up to 5 fans 6 can /can 9 inch) can be controlled by one DX-CON. Up to to 22 fans fans (size 12 inch) inch) can be controlled controlled by one one DX-CON. DX-CON. Up (size 12 be by Up to 2 fans (size can 12 inch) can be controlled by one DX-CON. Do not not mix mix different fan sizes sizes fan on the the same controller. Do fan on same controller. Dodifferent not mix different sizes on the same controller.
2
2
Liftand up remove panel and remove screws to unit. dismantle unit. Lift Lift up up panel panel and remove two two screws screwstwo to to dismantle dismantle unit.
3
3
1.5m 1.5m
Push Push out out backplate backplate Push out box box backplate cable cable entry entry box cable using usingentry aa screwdriver. screwdriver. using a screwdriver.
4
4
1.5m
Spotbackplate through backplate boxand andplug drillthe andceiling. plug the ceiling. Spot box Spot through through backplate box and and drill drill and plug the ceiling.
5
5
200mm 200mm 200mm
Fix Fix backplate backplate Fix box box backplate to to the thebox prepared prepared to theceiling. ceiling. prepared ceiling.
Feed Feed approx. approx. Feed 200mm 200mm approx.of of200mm supply supply cable cable of supply into into the cable the box box into the box
6
7
6
Connect end the cable block. Connect the the Connect end of ofthe theend cable ofinto into the the cable the control control into the block. control block.
LAB1345R (version 1) April 2018
7
Fit Fit the the control control Fit the into into control the the backplate backplate into the box box backplate and and secure. secure. box and secure. Test Test the the installation. installation. Test the installation.
Page 7
Installation and Maintenance DX Ceiling Fan Kit 50Hz/ 60Hz
V EN T IL AT ION
6.0 6.0Ancillaries Ancillaries 7.0 Maintenance
9.0 Warranty
Periodically, at least once a year or more frequently in case of heavy use, remove the dirt and encrustation from the grille(s) fan impeller and motor casing. Ensure the impeller is not cracked or deformed and is able to rotate freely and without oscillation.
The 2 year warranty starts from the day of delivery and includes parts and labour for the first year. The remaining period covers replacement parts only.
This warranty is void if the equipment is modified without authorisation, is incorrectly applied, misused, disassembled, or not installed, commissioned and maintained in accordance with the details Flexible Ducting and Installation Accessories Flexible Ducting and Installation Accessories contained in this manual and general good practice. A full range of range ducting installation accessories is available from A full ofand ducting and installation accessories is available from Used Usedininconjunction conjunction with withflexible flexibleducting ductingsystems. systems. 8.0 Replacement Of Parts Installation or replacement of units or spare parts must be carried out Domus. Domus. Mounted Mountedonto ontothe the frontofof the theSpacer Spacer sectionusing using the4event 4offoff5mm 5mmx x As a manu facturer Domus isfront aware that time is section important. Inthe the by a qualified or Domus approved service engineer/ electrician and in 40mm 40mmbrass screwssupplied supplied with withthe theSingle SingleSpigot Spigot Adaptor. Adaptor.Replaces Replaces of a breakdown ofbrass thisscrews equipment, it should be adequately packaged accordance with IEE or local national wiring regulations. the theinternal internal grille. grille. and returned to Domus. The product warranty applies to the UK mainland and in accordance Can Canalso alsobe beused used connected connected directly directly toa aRoof Terminal Terminal using using the the4 4offoff Please telephone Domus before posting yourto unit. ARoof returns number will with Clause 14 of our Conditions of Sale. 5mm x 40mm x 40mm brass brass screws screwssupplied suppliedwith withthe theSingle SingleSpigot Spigot Adaptor. Adaptor. be issued5mm to identify your package Customers purchasing from outside of the UK should contact Domus Manufactured Manufacturedfrom fromHIPS HIPSmaterial. material. Sales office for further details. A unit returned to Domus should be suitably protectively packaged and clearly marked with the ‘returns number’ obtained from Domus prior to posting. 9.0 Warranty 9.0 Warranty Do not use any solvents to clean this product. Single SingleSpigot SpigotAdaptor Adaptor
7.0 7.0Maintenance Maintenance
The 3 year The warranty 3 year warranty startsSales from starts the from day of the delivery day of and delivery includes and includes parts parts 10.0 After Enquiries Periodically, Periodically,atatleast leastonce oncea year a yearorormore morefrequently frequentlyinincase caseofofheavy heavy and labour andfor labour the first for year. the first Theyear. remaining The remaining period covers periodreplacement covers replacement use, use,remove removethe thedirt dirtand andencrustation encrustationfrom fromthe thegrille(s) grille(s)fan fanimpeller impeller For only. technical assistance or further product information, including spare parts parts and andmotor motorcasing. casing.Ensure Ensurethe theimpeller impelleris isnot notcracked crackedorordeformed deformedand andis isonly. parts and replacement components, please contact the After Sales able abletotorotate rotatefreely freelyand andwithout withoutoscillation. oscillation. This warranty This warranty is void iftthe ison void equipment if the715 equipment is modified is modified without without Departmen 03443 523 authorisation, authorisation, is incorrectly is incorrectly applied, misused, applied, misused, disassembled, disassembled, or not or not DoDonot notuse useany anysolvents solventstotoclean cleanthis thisproduct. product. installed, installed, commissioned commissioned and maintained and maintained in accordance in accordance with the details the details Technical or commercial considerations may, from time to time, make it necessary to alter the design, performance and dimensions ofwith equipment contained contained in this manual in thisand manual general andgood general practice. good practice. and the right is reserved to make such changes without prior notice. 8.0 8.0Replacement ReplacementOfOfParts Parts Installation Installation or replacement or replacement of units or of spare units or parts spare must parts be must carried beout carried out AsAsa amanufacturer manufacturerDomus Domusis isaware awarethat thattime timeis isimportant. important.InInthe theevent event Domus approved service engineer/ electrician by a qualified by a qualified or Domusorapproved service engineer/ electrician and in and in ofofa abreakdown breakdownofofthis thisequipment, equipment,it itshould shouldbebeadequately adequatelypackaged packaged accordance with IEEnational or local national wiring regulations. accordance with IEE or local wiring regulations. and andreturned returnedtotoDomus. Domus. The warranty product warranty the UK mainland and in accordance The product applies toapplies the UKtomainland and in accordance Please Pleasetelephone telephoneDomus Domusbefore beforeposting postingyour yourunit. unit. A Areturns returnsnumber number will will with14Clause of our Conditions with Clause of our14 Conditions of Sale. of Sale. bebeissued issuedtotoidentify identifyyour yourpackage. package. Customers purchasing fromof outside the UKcontact shouldDomus contact Domus Customers purchasing from outside the UKofshould We Wewill willendeavour endeavourtotorepair repairororreplace replaceit itwithin withinfive fiveworking workingdays daysofof Sales fordetails. furtherAdetails. A unit returned Domusbeshould be Sales office foroffice further unit returned to Domustoshould receipt. receipt.See Seeour ourwarranty warrantyterms. terms. suitably protectively andmarked clearlywith marked suitably protectively packagedpackaged and clearly the with the ‘returns number’ fromprior Domus prior to posting. ‘returns number’ obtainedobtained from Domus to posting.
10.0 After 10.0Sales AfterEnquiries Sales Enquiries For technical For technical assistance assistance or furtherorproduct further information, product information, includingincluding spare spare parts andparts replacement and replacement components, components, please contact pleasethe contact Afterthe Sales After Sales Department. Department. Technical or Technical commercial or commercial considerations considerations may, from may, time to from time, time make to time, it necessary make it to necessary alter thetodesign, alter the performance design, performance and dimensions and dimensions of equipment of equipment and the right andisthe reserved right istoreserved make such to make changes suchwithout changes prior without notice. prior notice.
VEN T IL AT ION Domus Ventilation Block C Caerphilly Business Park Van Road Caerphilly CF83 3ED Tel: +44 (0)3443 715523 Fax: +44 (0)3443 715524 Email:
[email protected] www.domusventilation.co.uk
LAB1345R May 2018
The EMC Directive 2014/30/EU The Low Voltage Directive 2014/35/EU
Page 8
