Adhesive

---

CSI 06 05 23

Listing Report:

FMS010909-5

PRODUCT: Adhesive (SIP) DIVISION: Wood and Plastics (06) SECTION: Wood, Plastic, and Composite Fastening (06 05 23) Report Holder

Foam Supplies, Inc. 4387 N. Rider Trail Earth City, Missouri 63045 Manufacturing Locations

Foam Supplies, Inc. 4387 N. Rider Trail Earth City, Missouri 63045 1. 1.1. 1.2. 1.3.

SUBJECT Foam Nail One Part-47 Polyurethane Adhesive Foam Nail One Part-20 Polyurethane Adhesive Foam Nail One Part-120 Polyurethane Adhesive

2. SCOPE 2.1. NTA, Inc. has evaluated the above product(s) as Type II Class 2 adhesives, acceptable for use in the construction of structural insulated panels (SIPs) when used with the materials and application instructions described in this report. NTA, Inc. has evaluated the above product(s) in accordance with: 2.2. NTA IM22 SEP02 SIP Panel Adhesives 2.3. NTA IM36 Quality System Requirements NTA, Inc. has evaluated the following properties of the above product(s): 2.4. Bond and Shear Strength 2.5. Long Duration Loads 2.6. Strength Loss due to accelerated weathering and moisture exposure To obtain the most current NTA Listing Report visit www.ntainc.com/product-certification/. 3. USES 3.1. General. Foam Nail Adhesives are One-part polyurethane adhesives used in the lamination of structural insulated panels.

3.2. Adhesive Classification. Foam Nail Adhesives shall be considered Type II Class 2 adhesives as defined in ICCES AC05. As such, the adhesive demonstrates high moisture and creep resistance and may be used in SIPs intended to support long duration loads other than the panel weight. 3.3. Compatible Materials. Foam Nail Adhesives are intended for bonding oriented strand board (OSB) and expanded poly-styrene (EPS) in structural insulated panels. 4. DESCRIPTION 4.1. General. Foam Nail Adhesives within the scope of this report are one-part moisture cure polyurethane adhesives. The adhesives are available in various size containers. Foam Nail Adhesives have a shelf life of 6 months from manufacturer date when stored in unopened containers between 50°F and 90°F. 5.

DESIGN The scope of this report is limited to Foam Nail One Part47, -20, or -120 polyurethane adhesives for use in Structural Insulated Panels. Details related to incorporation of the product beyond that scope are the responsibility of the designer of record. 5.1. Application. Foam Nail Adhesives within the scope of this report may be applied in a continuous thin film, or by bead application, to achieve a uniform coating. The coating is applied to one of the substrates to be bonded. After application of the adhesive to the substrate, a uniform coating of water is applied to the adhesive to activate it. Table 1 contains the evaluated application rates and conditions for the adhesives. 5.2. Curing Conditions. Open time, close time, and press time are specified for each adhesive should be in accordance with the manufacturer’s application instructions. Table 2 contains the evaluated curing conditions for the adhesive. 5.3. Allowable Loads. Allowable loads may not exceed the allowable values found in Table 3 or the allowable strength of the materials being bonded, whichever is less. The loads listed in Table 3 are applicable to the adhesives only and do not take into account the allowable stresses of any compatible materials. 6.

INSTALATION

This listing report is intended to indicate that NTA Inc. has evaluated product described and has found it to be eligible for labeling. Product not labeled as specified herein is not covered by this report. NTA Inc. makes no warranty, either expressed or implied, regarding the product covered by this report. NTA, INC. • 305 NORTH OAKLAND AVENUE • P.O. BOX 490 • NAPPANEE, INDIANA 46550 WEB: WWW.NTAINC.COM FMS010909-5 Listing Report

PHONE: 574-773-7975 FAX: 574-773-2260 Issue/Renewal Date: 2012-12-04 This report is subject to annual renewal.

NTA FORM ISQA 3.2n Listing Report Template 2012-03-21

Page 1 of 3

CSI 06 05 23

Listing Report: 6.1. General. All substrates to be bonded with Foam Nail Adhesives shall be clean and dry. Application method, the amount of adhesive, the amount of water, and the curing instructions shall be in accordance with the manufacturer’s application instructions. 7. CONDITIONS OF USE 7.1. Foam Nail Adhesives as described in this report comply with the codes listed in Section 2 above, subject to the following conditions: 7.1.1. Adhesives are manufactured in accordance with this report; the manufacturer’s published installation instructions, and the applicable code. 7.1.2. Long duration loads may not exceed the allowable values found in Table 3 or the allowable strength of the materials being bonded, whichever is less. 7.1.3. Adhesives are manufactured at the facility(s) listed in this report. 7.1.4. Adhesive may not be used with materials where fire retardant or preservative treatment is involved. 7.1.5. Adhesive is suitable for uses with limited exposure to the weather during installation; it is to be separated from the exterior by a code approved weather resistive barrier. 8. EVIDENCE SUBMITTED NTA, Inc. has examined the following evidence to evaluate this product: 8.1. Review of plant quality assurance manual in accordance with NTA IM 036, NTA IM 22 8.2. Plant certification inspection of manufacturer’s production facilities, test procedures, frequency and quality control sampling methods, test equipment and equipment calibration procedures, test records, dates and causes of failures when applicable in accordance with IM 036, NTA IM 22. 8.3. Qualification test data in accordance with NTA IM 22 Standard Evaluation Plan 02 (IM22 SEP02). 8.4. Periodic quality assurance audits of the production facility(s). 8.5. Periodic verification testing in accordance with NTA IM 22 Standard Evaluation Plan 02 (IM22 SEP02).

FMS010909-5

The scope of accreditation related to testing, inspection or product certification pertain only to the test methods and/or standard referenced therein. Design parameters and the application of building code requirements, such as special inspection, have not been reviewed by IAS and are not covered in the accreditation. Product evaluations are performed under the direct supervision of Professional Engineers licensed in all jurisdictions within the United States as required by the building code and state engineering board rules. 9. FINDINGS All products referenced herein are manufactured under an in-plant Quality Assurance program to insure that the production quality meets or exceeds the requirements of the codes noted herein and the criteria as established by NTA, Inc. Furthermore, product must comply with the conditions of this report. This report is subject to annual renewal. 10. IDENTIFICATION Each eligible product shall be permanently marked to provide the following information: 10.1. The NTA, Inc. listing mark, shown below 10.2. NTA’s Listing No. FMS010909-5 10.3. Identifier for production facility 10.4. Batch number 10.5. Production date 10.6. Statement of storage life

Evaluation evidence and data are on file with NTA, Inc. NTA, Inc.is accredited by the International Accreditation Service (IAS) as follows: ISO17020 Inspection Agency (AA-682) ISO17025 Testing Laboratory (TL-259) ISO Guide 65 Product Certification Agency (PCA-102)

This listing report is intended to indicate that NTA Inc. has evaluated product described and has found it to be eligible for labeling. Product not labeled as specified herein is not covered by this report. NTA Inc. makes no warranty, either expressed or implied, regarding the product covered by this report. NTA, INC. • 305 NORTH OAKLAND AVENUE • P.O. BOX 490 • NAPPANEE, INDIANA 46550 WEB: WWW.NTAINC.COM FMS010909-5 Listing Report

PHONE: 574-773-7975 FAX: 574-773-2260 Issue/Renewal Date: 2012-12-04 This report is subject to annual renewal.

NTA FORM ISQA 3.2n Listing Report Template 2012-03-21

Page 2 of 3

CSI 06 05 23

Listing Report:

FMS010909-5

Table 1: Nominal Application Specifications Adhesive

Application Method

One-Part-120 One-Part-20 One-Part-47

Bead or Roll Coat Bead or Roll Coat Bead or Roll Coat

Adhesive One-Part-120 One-Part-20 One-Part-47

Adhesive Applied 2 12 g/ft 2 12 g/ft 2 12 g/ft

Water Applied 2 g/ft2 2 g/ft2 2 g/ft2

Ambient Temp 73.4°F 73.4°F 73.4°F

Table 2: Nominal Curing Specifications 1 Closed Time2 Press Time3 Open Time 0.5 min 1.0 min 6 min 1.25 min 11.25 min 67 min 3 min 30 min 300 min

Ambient RH 50% 50% 50%

Press Pressure 3 psi 3 psi 3 psi

1

Open Time is defined as the maximum amount of time elapsed from adhesive application until the adhesive is covered with another substrate Closed Time is the maximum cumulative amount of time elapsed from the adhesive application, when it is covered with another substrate, until the assembly is under pressure 3 Press Time is the minimum amount of time the assembly is maintained under pressure 2

.

Adhesive One-Part-120 One-Part-20 One-Part-47

Table 3: Allowable Loads Allowable Shear Stress1 35 psi 40 psi 40 psi

1

Allowable Shear Stress is based on the most restrictive results from testing adhesives under long duration, tension, or shear loads and does not take into account the allowable stresses of any compatible materials.

This listing report is intended to indicate that NTA Inc. has evaluated product described and has found it to be eligible for labeling. Product not labeled as specified herein is not covered by this report. NTA Inc. makes no warranty, either expressed or implied, regarding the product covered by this report. NTA, INC. • 305 NORTH OAKLAND AVENUE • P.O. BOX 490 • NAPPANEE, INDIANA 46550 WEB: WWW.NTAINC.COM FMS010909-5 Listing Report

PHONE: 574-773-7975 FAX: 574-773-2260 Issue/Renewal Date: 2012-12-04 This report is subject to annual renewal.

NTA FORM ISQA 3.2n Listing Report Template 2012-03-21

Page 3 of 3