[PDF]architectural details - Dash Doord0a5a114441964e66f5b-0cbc9ea2dd077292aca26784763801f6.r78.cf2.rackcdn.co...
46 downloads
172 Views
718KB Size
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
AutoFlow ® Automatic Series 9331
F2.8 July 10
Type: 3-Wing with Segmented® Drum, Medium Stile
Standard Packages
10'-0" (3048)
10'-3 1/2" (3137)
Entry
Rough Opening Width
4'-4 3/4" (1340)
10'- 4" (3150)
Ceiling Height: 7'- 0" (2134),
Rough Opening Overall Height Unit Height 8'- 0" (2438)
Canopy Height: 12" (305)
Glazing: Standard unit prep'd for 1/4" (6) glass. Glass provided by others.
8'- 0 1/4" (2445) Anodized Finish: Clear or Dark Bronze
Options Custom ceiling height up to 9'-0". Ceiling lights. Aluminum roof.
Motion Sensor
Overall Unit Height
Outside Diameter
Nominal Inside Diameter
Extended, cropped or round canopy. Prep up to 1" glazing in door wings & drum. Custom anodized or paint finish.
Slow Speed Switch
For more standards & options see Architectural Specs (p.F5.0) and Spec Details (p. F3.0).
Outside Diameter
Installation and Operation Motion sensor at each entry starts wing rotation on user approach at 3-5 RPM. Push plate mounted at door entry slows door to 1-3 RPM for slower traffic.
Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling Felt Sweep with Reinf. Vinyl C337
1 5/8" (41)
4" (101)
1 3/8" (35)
Inside Drum Radius Door wIngs can be collapsed for Emergency Egress with 80-130 lbs (355-578 N) of force (adjustable).
VistaScan™ Safety Sensor
5/8" (16)
7'-0" (2134) Ceiling Height
Overall Unit Height
C336
(57)
2 1/4"
C369 Glass Stop
Muntin Bar C337
6 1/2" (165) Finish Floor 7/8"(22)
2" (51)
Drum Vertical Section
Door Wing Vertical Section
1/2" (13)
4" (102) Dia. Bottom Bearing Post
6" (194) Max. FootGuard™
1/2" (13) C2935
C363
3 3/4" (95)
C363
C338 Glass Stop
1/2" (13)
3 3/4" (95)
Felt Sweep with Reinf. Vinyl
Door Wing and Drum - Horizontal Section 3 3/16" (81) Safety Edge 1 1/2" (38) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
Bottom Spider with Bearing
5 93 C2
6 1/2" (165)
FootGuard™ Safety Switch
4" (101)
C283
3'-9 7/8" (1165)
Offset Glass Stops: C2934 & C340 C283
Floor Plan and Exterior Elevation Outside Drum Radius
3/4" (19) 1 1/2" (38) Mechnical Breakout
3/4"(19)
Slow Speed Switch
Entry
Pivot
2 1/4"
1/8" (3) Alum. Panels
Broken Out Position
Optional .090 aluminum roof
C363
C337-4
Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy.
12" (305) Canopy Height
2 1/4"
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Lock into ceiling (2 wings)
C283
Surface Mounted Bottom Bearing Post
) " (79 3 1/8
6" 3/1 2 1 1) (7
5/16" (8)
Bottom Bearing
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
AutoFlow ® Automatic Series 9330
F2.9 July 10
Type: 3-Wing with Round Drum, Medium Stile
Standard Packages Outside Drum Diameter
Outside Canopy Diameter
Entry
Rough Opening Width
Overall Unit Height
Rough Opening Height
10'-0" (3048)
10'-3 1/2" (3137)
10'-4" (3150)
4'-7 3/8" (1407)
10'- 4 1/2" (3162)
8'- 0" (2438)
8'- 0 1/4" (2445)
Ceiling Height: 7'- 0" (2134), Canopy Height: 12" (305) Anodized Finish: Glazing: Standard wing prep'd for 1/4" (6) glass. Glass provided by others. Clear or Dark Bronze Standard drum provided with 7/16" clear laminated curved glass.
Options Ceiling lights. Aluminum roof.
Custom ceiling height to 9'-0". Extended or cropped canopy.
Motion Sensor
Overall Unit Height
Nominal Inside Diameter
Slow Speed Switch
Prep to 1" glazing in wings & 9/16" in drum. Custom anodized or paint finish.
For more standards & options see Architectural Specs (p.F5.0) and Spec Details (p. F3.0). Outside Drum Diameter
Installation and Operation Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Motion sensor at each entry starts wing rotation on user approach at 3-5 RPM. Push plate mounted at door entry slows door to 1-3 RPM for slower traffic. Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy.
Broken Out Position 12" (305) Canopy Height
Optional .090 aluminum roof
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling Felt Sweep with Reinf. Vinyl
Floor Plan and Exterior Elevation Outside Canopy Radius Outside Drum Radius
1 5/8" (41)
(35)
C337
C2957
6 1/2" (165)
C283
4" (101)
7'-0" (2134) Ceiling Height
Muntin Bar
FootGuard™ Safety Switch
Finish Floor
3'-9 7/8" (1165)
(57)
2 1/4"
C369 Glass Stop
4" (101)
Overall Unit Height
C336
5/8" (16)
7/8"(22)
2" (51)
Drum Vertical Section
Door Wing Vertical Section
1/2" (13)
1/4" (13)
Door wIngs can be collapsed for Emergency Egress with 80-130 lbs (355-578 N) of force (adjustable).
VistaScan™ Safety Sensor 4" (102) Dia. Bottom Bearing Post
6" (194) Max.
1/2" (13)
FootGuard™
C2955 C363
3 3/4" (95)
C363
C338 Glass Stop
3 3/4"
1/2" (13)
(95)
Felt Sweep with Reinf. Vinyl
Door Wing and Drum - Horizontal Section 3 3/16" (81) 1 1/2" (38) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
Bottom Spider with Bearing
Pivot
4" (101)
1 3/8"
Inside Drum Radius
4" (101)
3/4" (19) 1 1/2" (38) Mechnical Breakout
1/4" (13)
Slow Speed Switch
Entry
C363
C2958
1/8" (3) Aluminum Facia
C2960
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Lock into ceiling (2 wings)
Safety Edge
py
1) (92 /8" 5 3 2) (13 6" 1 / 53
C283
Surface Mounted Bottom Bearing Post
o an fC e o ov e n i L Ab
5/16" (8)
Bottom Bearing
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
MiniGrand® Automatic Series 9331MG
F2.10 July 10
Type: 3-Wing with Segmented® Drum
Standard Packages
11'-0" (3353) 12'-0" (3658)
Inside Diameter
Overall Unit Height
Entry
10'-8 1/2" (3264) 4'-9 3/4" (1467) 11'-8 1/2" (3569) 5'-3 3/4" (1619)
Ceiling Height: 7'- 0" (2134).
Rough Opening Width Height
8'- 0" (2438) 11'-0 1/2" (3366) 8'-0 1/4" 8'- 0" (2438) 12'-0 1/2" (3670) 8'-0 1/4"
Canopy Height: 12" (305).
Glazing: Standard unit prep'd for 1/4" (6) glass. Glass provided by others.
Anodized Finish: Clear or Dark Bronze
Options Extended, cropped or round canopy. Aluminum roof.
Motion Sensor
Overall Unit Height
Nominal Outside Diameter
Slow Speed Switch
Prep up to 1" glazing in door wings & drum. Custom anodized or paint finish.
For more standards & options see Architectural Specs (p.F6.0) and Spec Details (p. F3.0).
Outside Diameter
Installation and Operation Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Motion sensors at each entry starts wing rotation on user approach at 3-5 RPM. Push plates mounted at each side of entry slow door to 1-3 RPM for slower traffic.
C337-4
Optional .090 aluminum roof
9" (229) Dia. Recessed Ceiling Lights
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling Felt Sweep with Reinf. Vinyl
Outside Drum Radius
7/16"
Inside Drum Radius
1 5/8" (41)
Magnetic Lock 1 3/8"
Armature (see p.F3.1)
(35)
Door wIngs can be collapsed for Emergency Egress after power is released from magnetic lock. Electromagnets hold wings in locked positions under normal conditions with 1000 lbs. min. force.
VistaScan™ Safety Sensor
(57)
2 1/4"
5/8"(16)
7'-0" (2134) Ceiling Height
Overall Unit Height
C2991 C369 Glass Stop
Muntin Bar C337
6 1/2" (165) 7/8"(22)
2" (51)
Drum Vertical Section
Door Wing Vertical Section
1/2" (13)
1/2" (13)
FootGuard™
C2935 C363
3 3/4" (95)
C363
C338 Glass Stop
3 3/4" (95)
1/2" (13)
Felt Sweep with Reinf. Vinyl
Door Wing and Drum - Horizontal Section 3 3/16" (81) Safety Edge 1 1/2" (38) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
Bottom Spider with Bearing
35
Finish Floor
6" (194) Max.
9 C2
6 1/2" (165)
FootGuard™ Safety Switch
4" (101)
C283 C283
3'-9 7/8" (1165)
Offset Glass Stops: C2934 & C340
3/4"(19)
4" (102) Dia. Bottom Bearing Post
Pivot
4" (101)
1 3/4"
1 1/4"
Slow Speed Switch
Floor Plan and Exterior Elevation
C337 C2980
Broken Out Position
Entry
C363
2 1/4"
1/8" (3) Alum. Panels
Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy.
12" (305) Canopy Height
2 1/4"
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Lock into ceiling (2 wings)
C283
Surface Mounted Bottom Bearing Post
3
9) " (7 1/8
/4" 13 ) (44
5/16" (8)
Bottom Bearing
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
MiniGrand® Automatic Series 9330MG
F2.11 July 10
Type: 3-Wing with Round Drum
Standard Packages
11'-0" (3353) 12'-0" (3658)
Inside Diameter
Rough Opening Width Height
Overall Unit Height
Entry
10'-8 1/2" (3264) 4'-7 5/8" (1413) 11'-8 1/2" (3569) 5'-1 5/8" (1565)
8'- 0" (2438)
11'-1" (3378)
8'-0 1/4"
8'- 0" (2438)
12'-1" (3683)
8'-0 1/4"
Motion Sensor
Overall Unit Height
Nominal Outside Diameter
Canopy Outside Diameter = Nominal O.D. + 1/2" (13). Anodized Finish: Ceiling Height: 7'- 0" (2134). Canopy Height: 12" (305). Clear or Dark Glazing: Standard wing prep'd for 1/4" (6) glass. Glass provided by others. Bronze Standard drum provided with 7/16" clear laminated curved glass.
Options
Slow Speed Switch
Prep up to 1" glazing in wings & 9/16" in drum. Custom anodized or paint finish.
Extended or cropped canopy. Aluminum roof.
Outside Diameter
For more standards & options see Architectural Specs (p.F6.0) and Spec Details (p. F3.0).
Installation and Operation Motion sensors at each entry starts wing rotation on user approach at 3-5 RPM. Push plates mounted at each side of entry slow door to 1-3 RPM for slower traffic. Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy.
12" (305) Canopy Height
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling Felt Sweep with Reinf. Vinyl C2980
1 1/4"
Broken Out Position
Floor Plan and Exterior Elevation Outside Canopy Radius Outside Drum Radius
7/16"
1 3/8"
Armature (see p.F3.1)
(35)
VistaScan™ Safety Sensor
6" (194) Max.
1/2" (13)
FootGuard™
Finish Floor 7/8"(22)
2" (51)
Drum Vertical Section
Door Wing Vertical Section
1/2" (13)
4" (102) Dia. Bottom Bearing Post
3 3/4" (95)
1/2" (13)
C2 Li n 95 eo 5 fC an 4" op y (1 A
bo ve
Door Wing and Drum Horizontal Section
01 )
3 3/16" (81) 1 1/2" (38) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
Bottom Spider with Bearing
Felt Sweep with Reinf. Vinyl
3 3/4" (95)
C363
C338 Glass Stop
Pivot
6 1/2" (165) C2957
FootGuard™ Safety Switch
C363
C363
C337
C283
4" (101)
7'-0" (2134) Ceiling Height
Muntin Bar
3'-9 7/8" (1165)
(57)
2 1/4"
C369 Glass Stop
4" (101)
Overall Unit Height
C2991
5/8"(16)
1/4" (6)
Door wIngs can be collapsed for Emergency Egress after power is released from magnetic lock. Electromagnets hold wings in locked positions under normal conditions with 1000 lbs. min. force.
1 5/8" (41)
Magnetic Lock
Slow Speed Switch
Entry
C2878
4" (101)
1 3/4"
1/4" (6)
9" (229) Dia. Recessed Ceiling Lights
Optional .090 aluminum roof
C2958
1/8" (3) Aluminum Facia
C2960
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Lock into ceiling (2 wings)
4" (101)
Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Safety Edge
C283
Surface Mounted Bottom Bearing Post
Bottom Bearing
5/16" (8)
1-1 95 C2
1) (92 /8" 5 3 2) (13 6" 1 / 53
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
ARCHITECTURAL DETAILS REVOLVING DOORS
Grand ® Automatic Series 9631 Type: 3-Wing with Segmented® Drum (page 1 of 3)
F2.12 July 10
Standard Packages Nominal Outside Diameter 12'-0" (3658) 14'-0" (4267) 16'-0" (4877)
Inside Diameter
Clear Access at Door Wing
Entry
Options
Rough Opening Width Height
Overall Unit Height
11'-8 1/2" (3569) 5'-3 3/4" (1619) 3'- 0 1/4" (921) 9'- 0" (2438) 12'-0 1/2" (3670) 9'-0 1/4" (2750) 13'-8 1/2" (4173) 6'-3 3/4" (1924) 4'- 0 1/4" (1226) 9'- 0" (2438) 14'-0 1/2" (4280) 9'-0 1/4" (2750) 15'-8 1/2" (4788) 7'-3 3/4" (2229) 5'- 0 1/4" (1530) 9'- 0" (2438) 16'-0 1/2" (4890) 9'-0 1/4" (2750)
Ceiling Height: 7'- 0" (2134).
Canopy Height: 24" (610).
Anodized Finish: Clear or Dark Bronze
Glazing: Standard unit prep'd for 1/4" (6) glass. Glass provided by others.
Installation and Operation
Custom ceiling height up to 8'-0". Extended, cropped or round canopy. Aluminum roof. Prep up to 1" glazing in door wings & drum. Custom anodized or paint finish.
For more standards & options see Architectural Specs (p.F7.0) and Spec Details (p. F3.0).
Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Motion sensors at each entry starts wing rotation on user approach at 3-5 RPM. Push plates mounted at each side of entry slow door to 1-3 RPM for slower traffic.
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy. Motion Sensor
For Horizontal Sections see F2.13 (page 2 of 3).
Overall Unit Height
For Vertical Sections see F2.14 (page 3 of 3).
Slow Speed Switch
Outside Diameter
Wing Lock
Core
2-0" (610)
Acce
9" (229) Dia. Recessed Ceiling Lights
ss P a
nel
Wing Lock
Display Core
Clear Access Broken Out Position
Entry
Slow Speed Switch
Floor Plan and Exterior Elevation
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
Grand ® Automatic Series 9631
F2.13 Jan 08
Type: 3-Wing with Segmented® Drum (page 2 of 3) 31 /8"
For Elevation & Floor Plan see F2.12 (page 1 of 3). For Vertical Sections see F2.14 (page 3 of 3).
Safety Edge
(79 )
13 /4" (44 )
C
29 3
5
Roton Hinge
3'3
" (9
91 )
Ac
90 7
Door wIngs can be collapsed for Emergency Egress after power is released from magnetic lock. Electromagnets hold wings in locked positions under normal conditions with 1000 lbs. min. force.
25 )
.09" Alum. Display Floor
3'- 3 3/8" (1000) Display Area
an el
1" (
1/2" (13)
95 2
1" (
25 )
Black Neoprene Fingerguard
C2
C340 & C2934 Offset Stops
ce ss P
2" (51) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
FootGuard™ C338 Glass Stop
C2949 Jamb
C2
C2
b am 9J 94
C2935 C363
1" (25)
C363
3 3/4" (95)
3 3/4" (95)
1/2" (13)
2" (51)
7 1/2" (191)
3/4"(19)
C2 94 9
7 1/2" (191) Aluminum Cover for Hydraulic Closer
2' - 1 3/4" (654) Ja mb
Inside Drum Radius Outside Drum Radius
/2"
Display Core, Door Wing and Drum - Horizontal Section )
9)
2" (51) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
C283
C363
Bottom Spider Assembly Connects to Hydaulic Closers Beyond
Alum. Cover for Hydraulic Closer
3 5/8" (92) C2920
Finish Floor
C2963
(65)
1/4" Alum. Panel
2 9/16"
(15
(89
Pivot
/4"
C2949 Jamb
61
Fingerguard
31
7/8"(22)
Bottom Bearing Within Core
1/2" (13)
Corner Detail at Closer Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
C337-4
REVOLVING DOORS
Grand ® Automatic Series 9631
Optional .090 aluminum roof
For Elevation & Floor Plan see F2.12 (page 1 of 3).
1/8" (3) Alum. Panels
For Horizontal Sections see F2.13 (page 2 of 3).
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling
Felt Sweep with Reinf. Vinyl C337
1" C2920-1
1 5/8" (41) 1 3/8" C2963
(35)
C2920-1
4 3/4" (121)
1 3/4" 4 13/16" (122)
Armature
VistaScan™ Safety Sensor
Cam Locks Top & Bottom 7/8"
C337 C338 Glass Stop
1/2"(13)
C337
(57)
2 1/4"
7/8" C2948
1/16"
C2948
C340 & C2934 Offset Stops
1/4" Alum. Panel
3/4"(19)
Display Core Access Panel Vertical Section
C2920
3" (76)
C2963
1'-9 7/8" (543) Core Metal Apron
4" (101)
FootGuard™ Safety Switch
(46)
Finish Floor
6 1/2" (165)
6 1/2" (165)
C283
C283
1 13/16"
3/4"(19)
3'-9 7/8" (1165)
3/4"(19)
Offset Glass Stops: C2934 & C340
(57)
1/4" Glass (by others)
.09" Alum. Display Floor
1/16"
C337
Roton Hinge
Muntin Bar
4'-8" (1422) Display Area
C369 Glass Stop
(57)
5/8"(16)
2 1/4"
.09" Alum. Display Ceiling
C325-1
2 1/4"
Overall Unit Height
Magnetic Lock
7/16"
4'-7 7/8" (1419) Access Panel
C2980
1 1/4"
7'-0" (2134) Ceiling Height
2 1/4"
F2.14 Jan 08
Type: 3-Wing with Segmented® Drum (page 3 of 3)
2 - 0" (305) Canopy Height
2 1/4"
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
7/8"(22)
7/8"(22)
2" (51) 1/2" (13)
1/2" (13)
Drum Vertical Section
Door Wing Vertical Section
Display Core Vertical Section Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
ARCHITECTURAL DETAILS REVOLVING DOORS
Grand ® Automatic Series 9630 Type: 3-Wing with Round Drum (page 1 of 3)
F2.15 July 10
Standard Packages Nominal Outside Diameter 12'-0" (3658) 14'-0" (4267) 16'-0" (4877)
Inside Diameter
Clear Access at Door Wing
Entry
Options
Rough Opening Width Height
Overall Unit Height
11'-8 1/2" (3569) 5'-1 5/8" (1565) 3'- 0 1/4" (921) 9'- 0" (2438) 12'-0 1/2" (3670) 9'-0 1/4" (2750) 13'-8 1/2" (4173) 6'-1 5/8" (1870) 4'- 0 1/4" (1226) 9'- 0" (2438) 14'-0 1/2" (4280) 9'-0 1/4" (2750) 15'-8 1/2" (4788) 7'-1 5/8" (2174) 5'- 0 1/4" (1530) 9'- 0" (2438) 16'-0 1/2" (4890) 9'-0 1/4" (2750)
Canopy Outside Diameter = Nominal O.D. + 1/2" (13). Ceiling Height: 7'- 0" (2134). Canopy Height: 24" (610). Glazing: Standard wing prep'd for 1/4" (6) glass. Glass provided by others. Standard drum provided with 7/16" clear laminated curved glass.
Anodized Finish: Clear or Dark Bronze
Custom ceiling height up to 8'-0". Extended or cropped canopy. Aluminum roof. Prep up to 1" glazing in door wings & 9/16" in drum. Custom anodized or paint finish.
For more standards & options see Architectural Specs (p.F7.0) and Spec Details (p. F3.0).
Installation and Operation Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Motion sensors at each entry starts wing rotation on user approach at 3-5 RPM. Push plates mounted at each side of entry slow door to 1-3 RPM for slower traffic.
Drum can be center connected to adjacent construction or throat connected (at entry vertical rails) (see p.F1.1). Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy. Motion Sensor
For Horizontal Sections see F2.16 (page 2 of 3).
Overall Unit Height
For Vertical Sections see F2.17 (page 3 of 3).
Slow Speed Switch
Outside Diameter
Wing Lock
Core
2-0" (610)
Acce
9" (229) Dia. Recessed Ceiling Lights
ss P a
nel
Wing Lock
Display Core
Clear Access Broken Out Position
Entry
Slow Speed Switch
Floor Plan and Exterior Elevation
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOORS
Grand ® Automatic Series 9631
F2.16 Jan 08
Type: 3-Wing with Round Drum (page 2 of 3) 53
For Vertical Sections see F2.17 (page 3 of 3).
/16
" (1 32 ) 35 /8" (92 1)
For Elevation & Floor Plan see F2.15 (page 1 of 3). Safety Edge
C2 9
51
-1
55
Black Neoprene Fingerguard
FootGuard™ C338 Glass Stop
C363
1" (25)
C363
3 3/4" (95)
3 3/4" (95)
1/2" (13)
7 1/2" (191)
3/4"(19)
C2 94 9
7 1/2" (191) Aluminum Cover for Hydraulic Closer
2' - 1 3/4" (654) Ja mb
Inside Drum Radius Outside Drum Radius
/2"
(89
Display Core, Door Wing and Drum - Horizontal Section
)
9)
2" (51) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
C283
Alum. Cover for Hydraulic Closer
3 5/8" (92) C2920
Finish Floor
C2963
(65)
C363
Bottom Spider Assembly Connects to Hydaulic Closers Beyond
2 9/16"
1/4" Alum. Panel
Pivot
(15
Fingerguard
/4"
1/4" (6)
Outside Canopy Radius
C2949 Jamb
31 61
2" (51)
4" (101)
2" (51) Dia. Steel Center Shaft with 1/32" (1) Stainless Steel Sleeve
C2878
25 )
C2878
1" (
1/2" (13)
4" (101)
Door wIngs can be collapsed for Emergency Egress after power is released from magnetic lock. Electromagnets hold wings in locked positions under normal conditions with 1000 lbs. min. force.
25 )
.09" Alum. Display Floor
3'- 3 3/8" (1000) Display Area
an el
95 2
1" (
C2
C340 & C2934 Offset Stops
ce ss P
C2949 Jamb
C2
90 7
Ac
ve bo
91 )
yA
" (9
p no Ca of
9 C2
C2
e Lin
3'3 b am 9J 94
1) (10 4"
Roton Hinge
7/8"(22)
Bottom Bearing Within Core
1/2" (13)
Corner Detail at Closer Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS REVOLVING DOORS
Grand ® Automatic Series 9631
Optional .090 aluminum roof
For Elevation & Floor Plan see F2.15 (page 1 of 3).
1/8" (3) Aluminum Facia
For Horizontal Sections see F2.16 (page 2 of 3).
3/4" (19) Plywood with .063" (1.6) Laminated Aluminum Ceiling
Felt Sweep with Reinf. Vinyl
1" C2920-1
1 5/8" (41) 1 3/8" C2963
(35)
C2920-1
4 3/4" (121)
1 3/4" 4 13/16" (122)
Armature
VistaScan™ Safety Sensor
Cam Locks Top & Bottom 7/8"
C338 Glass Stop
1/2"(13)
C337
4" (101)
(46)
C2963
(57)
2 1/4"
7/8" C2948
1/16"
C2948
C340 & C2934 Offset Stops
1/4" Alum. Panel
3/4"(19)
Display Core Access Panel Vertical Section
C2920
3" (76)
6 1/2" (165) 1 13/16"
C2957
Finish Floor
FootGuard™ Safety Switch
1'-9 7/8" (543) Core Metal Apron
3'-9 7/8" (1165)
3/4"(19)
C283
(57)
1/4" Glass (by others)
.09" Alum. Display Floor
1/16"
C337
Roton Hinge
C337
4'-8" (1422) Display Area
Muntin Bar
7'-0" (2134) Ceiling Height
C369 Glass Stop
(57)
5/8"(16)
2 1/4"
.09" Alum. Display Ceiling
C325-1
2 1/4"
Overall Unit Height
Magnetic Lock
7/16"
4'-7 7/8" (1419) Access Panel
C2980
1 1/4"
1/4" (6)
4" (101)
F2.17 Jan 08
Type: 3-Wing with Round Drum (page 3 of 3)
2 - 0" (305) Canopy Height
C2960
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
7/8"(22)
7/8"(22)
2" (51) 1/2" (13)
1/2" (13)
Drum Vertical Section
Door Wing Vertical Section
Display Core Vertical Section Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.
ARCHITECTURAL DETAILS
® 4242 Baldwin Boulevard Corpus Christi, Texas USA 78405-3399 Tel: 800-531-3111, 361-888-5591 Fax: 800-531-3108, 361-888-6510 www.hortondoors.com A U T O M A T I C S The Automatic Choice
REVOLVING DOOR ENTRANCES
Grand ® Automatic Series 9620
Standard Packages Nominal Outside Diameter
Inside Diameter
12'-1 3/16" (3688)
11'-9 3/4" (3600)
5'-10 7/8"
(1800)
3'-7 5/16" (1100)
12'-1 3/4" (3670)
14'-0 13/16" (4288) 16'-0 7/16" (4888)
13'-9 1/4" (4200)
6'-10 11/16" (2100)
4'-7 1/16" (1400)
14'-1 3/8" (4280)
15' - 9"
7'-10 1/2"
5'-6 15/16" (1700)
16'-1"
(4800)
Ceiling Height: 7'-6 9/16" (2300) Canopy Height: 1'-1 3/8" (340) Overall Unit Height: 8'-7 15/16" (2640)
F2.18 Apr 13
Type: 2-Wing with Round Drum
Entry / Breakout Opening
(2400)
Slide Door Opening
Rough Opening Width
Options Extended canopy. Aluminum roof.
(4890)
Glazing: Prep for 1/4" glazing in door wings & 5/16" in drum. Finishes: Anodized or paint finish or stainless steel cladding
Installation and Operation Motion sensors at each entry starts wing rotation on user approach at 3-5 RPM. Push plates mounted at each side of entry slow door to 1-3 RPM for slower traffic.
Drum can be center connected to adjacent construction. Allow 1/4" shim space each side & at canopy. Adjacent construction not to bear down on revolving door.
Electrical: Provide 120 VAC, 15 amp service on a dedicated 20 amp circuit breaker routed to power operator mounted within the enclosure canopy.
Overall Unit Height
Door unit is surface mounted to finish floor (floor not to exceed 1/4" out of level). Unit is free-standing with no additional support required.
Outside Diameter
Slide Door Opening
Breakout Opening
Entry
Floor Plan and Exterior Elevation
Horton Automatics reserves the right to alter its product and specifications without notice. Dimensions given in U.S. inches followed by millimeters in parenthesis.