dunlop aac concrete block adhesive

---

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 1 of 11

Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME DUNLOP AAC CONCRETE BLOCK ADHESIVE SYNONYMS "Thin Bed Cement Adhesive" PRODUCT USE Adhesive mortar for AAC concrete blocks. SUPPLIER Company: Ardex Australia Pty Ltd Address: 20 Powers Road Seven Hills NSW, 2147 Australia Telephone: 1800 224 070 Emergency Tel: 1800 222 841 Fax: +61 2 9838 7817

Section 2 - HAZARDS IDENTIFICATION STATEMENT OF HAZARDOUS NATURE HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of NOHSC, and the ADG Code. CHEMWATCH HAZARD RATINGS Flammability Toxicity Body Contact Reactivity Chronic SCALE: RISK Risk Codes R38 R41 SAFETY Safety Codes S24 S25 S37 S39 S401 S26

Min/Nil=0

Low=1

Moderate=2

High=3

Extreme=4

Risk Phrases • Irritating to skin. • Risk of serious damage to eyes. Safety Phrases • Avoid contact with skin. • Avoid contact with eyes. • Wear suitable gloves. • Wear eye/face protection. • To clean the floor and all objects contaminated by this material, use water and detergent. • In case of contact with eyes, rinse with plenty of water and contact Doctor or Poisons Information Centre. continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

S46

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 2 of 11 Section 2 - HAZARDS IDENTIFICATION

• If swallowed, IMMEDIATELY contact Doctor or Poisons Information Centre. (show this container or label).

Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS NAME cement as, portland cement graded sand cellulose thickener polymer additive

CAS RN 65997-15-1 14808-60-7.

% 10-60 10-60 0-1 0-1

Section 4 - FIRST AID MEASURES SWALLOWED • Immediately give a glass of water. • First aid is not generally required. If in doubt, contact a Poisons Information Centre or a doctor. EYE ■ If this product comes in contact with the eyes: • Immediately hold eyelids apart and flush the eye continuously with running water. • Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids. • Continue flushing until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes. • Transport to hospital or doctor without delay. • Removal of contact lenses after an eye injury should only be undertaken by skilled personnel. SKIN ■ If skin contact occurs: • Immediately remove all contaminated clothing, including footwear. • Flush skin and hair with running water (and soap if available). • Seek medical attention in event of irritation. INHALED • If fumes, aerosols or combustion products are inhaled remove from contaminated area. • Other measures are usually unnecessary. NOTES TO PHYSICIAN ■ Treat symptomatically. Section 5 - FIRE FIGHTING MEASURES EXTINGUISHING MEDIA • There is no restriction on the type of extinguisher which may be used. • Use extinguishing media suitable for surrounding area. FIRE FIGHTING • Alert Fire Brigade and tell them location and nature of hazard. • Wear breathing apparatus plus protective gloves in the event of a fire. • Prevent, by any means available, spillage from entering drains or water courses. • Use fire fighting procedures suitable for surrounding area. • DO NOT approach containers suspected to be hot. continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 3 of 11 Section 5 - FIRE FIGHTING MEASURES

• Cool fire exposed containers with water spray from a protected location. • If safe to do so, remove containers from path of fire. • Equipment should be thoroughly decontaminated after use. FIRE/EXPLOSION HAZARD • Non combustible. • Not considered a significant fire risk, however containers may burn. Decomposition may produce toxic fumes of: metal oxides. May emit poisonous fumes. FIRE INCOMPATIBILITY ■ None known. HAZCHEM None Section 6 - ACCIDENTAL RELEASE MEASURES MINOR SPILLS • Clean up all spills immediately. • Avoid breathing dust and contact with skin and eyes. • Wear protective clothing, gloves, safety glasses and dust respirator. • Use dry clean up procedures and avoid generating dust. • Sweep up, shovel up or • Vacuum up (consider explosion-proof machines designed to be grounded during storage and use). • Place spilled material in clean, dry, sealable, labelled container. MAJOR SPILLS ■ Moderate hazard. • CAUTION: Advise personnel in area. • Alert Emergency Services and tell them location and nature of hazard. • Control personal contact by wearing protective clothing. • Prevent, by any means available, spillage from entering drains or water courses. • Recover product wherever possible. • IF DRY: Use dry clean up procedures and avoid generating dust. Collect residues and place in sealed plastic bags or other containers for disposal. IF WET: Vacuum/shovel up and place in labelled containers for disposal. • ALWAYS: Wash area down with large amounts of water and prevent runoff into drains. • If contamination of drains or waterways occurs, advise Emergency Services. Personal Protective Equipment advice is contained in Section 8 of the MSDS. Section 7 - HANDLING AND STORAGE PROCEDURE FOR HANDLING • Avoid all personal contact, including inhalation. • Wear protective clothing when risk of exposure occurs. • Use in a well-ventilated area. • Prevent concentration in hollows and sumps. • DO NOT enter confined spaces until atmosphere has been checked. • DO NOT allow material to contact humans, exposed food or food utensils. • Avoid contact with incompatible materials. • When handling, DO NOT eat, drink or smoke. • Keep containers securely sealed when not in use. continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 4 of 11 Section 7 - HANDLING AND STORAGE

• Avoid physical damage to containers. • Always wash hands with soap and water after handling. • Work clothes should be laundered separately. Launder contaminated clothing before re-use. • Use good occupational work practice. • Observe manufacturer's storage and handling recommendations contained within this MSDS. • Atmosphere should be regularly checked against established exposure standards to ensure safe working conditions are maintained. SUITABLE CONTAINER • Polyethylene or polypropylene container. • Check all containers are clearly labelled and free from leaks. STORAGE INCOMPATIBILITY • Metals and their oxides or salts may react violently with chlorine trifluoride and bromine trifluoride. • These trifluorides are hypergolic oxidisers. They ignites on contact (without external source of heat or ignition) with recognised fuels - contact with these materials, following an ambient or slightly elevated temperature, is often violent and may produce ignition. • The state of subdivision may affect the results. STORAGE REQUIREMENTS • Store in original containers. • Keep containers securely sealed. • Store in a cool, dry area protected from environmental extremes. • Store away from incompatible materials and foodstuff containers. • Protect containers against physical damage and check regularly for leaks. • Observe manufacturer's storage and handling recommendations contained within this MSDS. For major quantities: • Consider storage in bunded areas - ensure storage areas are isolated from sources of community water (including stormwater, ground water, lakes and streams}. • Ensure that accidental discharge to air or water is the subject of a contingency disaster management plan; this may require consultation with local authorities. Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION EXPOSURE CONTROLS The following materials had no OELs on our records • graded sand:

CAS:14808- 60- 7

EMERGENCY EXPOSURE LIMITS Material Revised IDLH Value (mg/m3) portland cement|13763 5, 000 graded sand|85014 50

Revised IDLH Value (ppm)

MATERIAL DATA DUNLOP AAC CONCRETE BLOCK ADHESIVE: PORTLAND CEMENT: ■ NOTE: This substance has been classified by the ACGIH as A4 NOT classifiable as causing Cancer in humans. DUNLOP AAC CONCRETE BLOCK ADHESIVE: PORTLAND CEMENT: ■ for calcium silicate: containing no asbestos and <1% crystalline silica ES TWA: 10 mg/m3 inspirable dust TLV TWA: 10 mg/m3 total dust (synthetic nonfibrous) A4 Although in vitro studies indicate that calcium silicate is more toxic than substances described as continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 5 of 11 Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION

"nuisance dusts" is thought that adverse health effects which might occur following exposure to 10-20 mg/m3 are likely to be minimal. The TLV-TWA is thought to be protective against the physical risk of eye and upper respiratory tract irritation in workers and to prevent interference with vision and deposition of particulate in the eyes, ears, nose and mouth. PORTLAND CEMENT: ■ For calcium oxide: The TLV-TWA is thought to be protective against undue irritation and is analogous to that recommended for sodium hydroxide. The concentration of dust, for application of respirable dust limits, is to be determined from the fraction that penetrates a separator whose size collection efficiency is described by a cumulative log-normal function with a median aerodynamic diameter of 4.0 µm (+-) 0.3 µm and with a geometric standard deviation of 1.5 µm (+-) 0.1 µm, i.e..generally less than 5 µm. Portland cement is considered to be a nuisance dust that does not cause fibrosis and has little potential to induce adverse effects on the lung. GRADED SAND: NOTE: This product contains negligible amount of respirable dust. PERSONAL PROTECTION EYE • Safety glasses with side shields. • Chemical goggles. • Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing of lens or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience. Medical and first-aid personnel should be trained in their removal and suitable equipment should be readily available. In the event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens should be removed at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers have washed hands thoroughly. [CDC NIOSH Current Intelligence Bulletin 59], [AS/NZS 1336 or national equivalent]. HANDS/FEET ■ The selection of the suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. The exact break through time for substances has to be obtained from the manufacturer of the protective gloves and has to be observed when making a final choice. Suitability and durability of glove type is dependent on usage. Important factors in the selection of gloves include: • frequency and duration of contact, • chemical resistance of glove material, • glove thickness and • dexterity Select gloves tested to a relevant standard (e.g. Europe EN 374, US F739, AS/NZS 2161.1 or national equivalent). • When prolonged or frequently repeated contact may occur, a glove with a protection class of 5 or higher (breakthrough time greater than 240 minutes according to EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended. • When only brief contact is expected, a glove with a protection class of 3 or higher (breakthrough time greater than 60 minutes according to EN 374, AS/NZS 2161.10.1 or national equivalent) is recommended. • Contaminated gloves should be replaced. Gloves must only be worn on clean hands. After using gloves, hands should be washed and dried thoroughly. Application of a non-perfumed moisturiser is recommended. continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 6 of 11 Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION

Experience indicates that the following polymers are suitable as glove materials for protection against undissolved, dry solids, where abrasive particles are not present. • polychloroprene • nitrile rubber • butyl rubber • fluorocaoutchouc • polyvinyl chloride Gloves should be examined for wear and/ or degradation constantly. OTHER • Overalls. • P.V.C. apron. • Barrier cream. • Skin cleansing cream. • Eye wash unit. RESPIRATOR •Particulate. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI Z88 or national equivalent) • Respirators may be necessary when engineering and administrative controls do not adequately prevent exposures. • The decision to use respiratory protection should be based on professional judgment that takes into account toxicity information, exposure measurement data, and frequency and likelihood of the worker's exposure ensure users are not subject to high thermal loads which may result in heat stress or distress due to personal protective equipment (powered, positive flow, full face apparatus may be an option). • Published occupational exposure limits, where they exist, will assist in determining the adequacy of the selected respiratory . These may be government mandated or vendor recommended. • Certified respirators will be useful for protecting workers from inhalation of particulates when properly selected and fit tested as part of a complete respiratory protection program. • Use approved positive flow mask if significant quantities of dust becomes airborne. • Try to avoid creating dust conditions. The local concentration of material, quantity and conditions of use determine the type of personal protective equipment required. For further information consult site specific CHEMWATCH data (if available), or your Occupational Health and Safety Advisor. ENGINEERING CONTROLS ■ Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Welldesigned engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection. The basic types of engineering controls are: Process controls which involve changing the way a job activity or process is done to reduce the risk. Enclosure and/or isolation of emission source which keeps a selected hazard "physically" away from the worker and ventilation that strategically "adds" and "removes" air in the work environment. Ventilation can remove or dilute an air contaminant if designed properly. The design of a ventilation system must match the particular process and chemical or contaminant in use. Employers may need to use multiple types of controls to prevent employee overexposure. • Local exhaust ventilation is required where solids are handled as powders or crystals; even when particulates are relatively large, a certain proportion will be powdered by mutual friction. • If in spite of local exhaust an adverse concentration of the substance in air could occur, respiratory protection should be considered. Such protection might consist of: (a): particle dust respirators, if necessary, combined with an absorption cartridge; (b): filter respirators with absorption cartridge or canister of the right type; (c): fresh-air hoods or masks.

continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 7 of 11

Section 9 - PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE Fine to medium grey coarse powder; partly soluble in water. PHYSICAL PROPERTIES State Melting Range (°C) Boiling Range (°C) Flash Point (°C) Decomposition Temp (°C) Autoignition Temp (°C) Upper Explosive Limit (%) Lower Explosive Limit (%)

Divided Solid Not Available Not Applicable Not Applicable Not Available Not Applicable Not Applicable Not Applicable

Volatile Component (%vol)

Not Applicable

Molecular Weight Viscosity Solubility in water (g/L) pH (1% solution) pH (as supplied) Vapour Pressure (kPa) Specific Gravity (water=1) Relative Vapour Density (air=1) Evaporation Rate

Not Applicable Not Applicable Partly Miscible Not Available 11- 12 Not Applicable Not Available Not Applicable Not Applicable

Section 10 - STABILITY AND REACTIVITY CONDITIONS CONTRIBUTING TO INSTABILITY • Presence of incompatible materials. • Product is considered stable. • Hazardous polymerisation will not occur. For incompatible materials - refer to Section 7 - Handling and Storage. Section 11 - TOXICOLOGICAL INFORMATION POTENTIAL HEALTH EFFECTS ACUTE HEALTH EFFECTS SWALLOWED ■ Not normally a hazard due to the physical form of product. The material is a physical irritant to the gastro-intestinal tract. EYE ■ If applied to the eyes, this material causes severe eye damage. SKIN ■ This material can cause inflammation of the skin oncontact in some persons. The material may accentuate any pre-existing dermatitis condition. Handling wet cement can cause dermatitis. Cement when wet is quite alkaline and this alkali action on the skin contributes strongly to cement contact dermatitis since it may cause drying and defatting of the skin which is followed by hardening, cracking, lesions developing, possible infections of lesions and penetration by soluble salts. Entry into the blood-stream, through, for example, cuts, abrasions or lesions, may produce systemic injury with harmful effects. Examine the skin prior to the use of the material and ensure that any external damage is suitably protected. INHALED ■ Persons with impaired respiratory function, airway diseases and conditions such as emphysema or chronic bronchitis, may incur further disability if excessive concentrations of particulate are inhaled. If prior damage to the circulatory or nervous systems has occurred or if kidney damage has been sustained, continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 8 of 11 Section 11 - TOXICOLOGICAL INFORMATION

proper screenings should be conducted on individuals who may be exposed to further risk if handling and use of the material result in excessive exposures. CHRONIC HEALTH EFFECTS ■ Long term exposure to high dust concentrations may cause changes in lung function i.e. pneumoconiosis; caused by particles less than 0.5 micron penetrating and remaining in the lung. Prime symptom is breathlessness; lung shadows show on X-ray. Substance accumulation, in the human body, may occur and may cause some concern following repeated or longterm occupational exposure. Cement contact dermatitis (CCD) may occur when contact shows an allergic response, which may progress to sensitisation. Sensitisation is due to soluble chromates (chromate compounds) present in trace amounts in some cements and cement products. Soluble chromates readily penetrate intact skin. Cement dermatitis can be characterised by fissures, eczematous rash, dystrophic nails, and dry skin; acute contact with highly alkaline mixtures may cause localised necrosis. Cement eczema may be due to chromium in feed stocks or contamination from materials of construction used in processing the cement. Sensitisation to chromium may be the leading cause of nickel and cobalt sensitivity and the high alkalinity of cement is an important factor in cement dermatoses [ILO]. Repeated, prolonged severe inhalation exposure may cause pulmonary oedema and rarely, pulmonary fibrosis. Workers may also suffer from dust-induced bronchitis with chronic bronchitis reported in 17% of a group occupationally exposed to high dust levels. Respiratory symptoms and ventilatory function were studied in a group of 591 male Portland cement workers employed in four Taiwanese cement plants, with at least 5 years of exposure (1). This group had a significantly lowered mean forced vital capacity (FCV), forced expiratory volume at 1 s (FEV1) and forced expiratory flows after exhalation of 50% and 75% of the vital capacity (FEF50, FEF75). The data suggests that occupational exposure to Portland cement dust may lead to a higher incidence of chronic respiratory symptoms and a reduction of ventilatory capacity. Chun-Yuh et al; Journal of Toxicology and Environmental Health 49: 581-588, 1996. TOXICITY AND IRRITATION ■ unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances. DUNLOP AAC CONCRETE BLOCK ADHESIVE: ■ No significant acute toxicological data identified in literature search. PORTLAND CEMENT: ■ Asthma-like symptoms may continue for months or even years after exposure to the material ceases. This may be due to a non-allergenic condition known as reactive airways dysfunction syndrome (RADS) which can occur following exposure to high levels of highly irritating compound. Key criteria for the diagnosis of RADS include the absence of preceding respiratory disease, in a non-atopic individual, with abrupt onset of persistent asthma-like symptoms within minutes to hours of a documented exposure to the irritant. A reversible airflow pattern, on spirometry, with the presence of moderate to severe bronchial hyperreactivity on methacholine challenge testing and the lack of minimal lymphocytic inflammation, without eosinophilia, have also been included in the criteria for diagnosis of RADS. RADS (or asthma) following an irritating inhalation is an infrequent disorder with rates related to the concentration of and duration of exposure to the irritating substance. Industrial bronchitis, on the other hand, is a disorder that occurs as result of exposure due to high concentrations of irritating substance (often particulate in nature) and is completely reversible after exposure ceases. The disorder is characterised by dyspnea, cough and mucus production. GRADED SAND: ■ No data of toxicological significance identified in literature search. CARCINOGEN

continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

graded sand

International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 9 of 11 Section 11 - TOXICOLOGICAL INFORMATION Group

1

Section 12 - ECOLOGICAL INFORMATION PORTLAND CEMENT: ■ For Metal: Atmospheric Fate - Metal-containing inorganic substances generally have negligible vapour pressure and are not expected to partition to air. Environmental Fate: Environmental processes, such as oxidation, the presence of acids or bases and microbiological processes, may transform insoluble metals to more soluble ionic forms. Environmental processes may enhance bioavailability and may also be important in changing solubilities. Aquatic/Terrestrial Fate: When released to dry soil, most metals will exhibit limited mobility and remain in the upper layer; some will leach locally into ground water and/ or surface water ecosystems when soaked by rain or melt ice. A metal ion is considered infinitely persistent because it cannot degrade further. Once released to surface waters and moist soils their fate depends on solubility and dissociation in water. A significant proportion of dissolved/ sorbed metals will end up in sediments through the settling of suspended particles. The remaining metal ions can then be taken up by aquatic organisms. Ionic species may bind to dissolved ligands or sorb to solid particles in water. Ecotoxicity: Even though many metals show few toxic effects at physiological pH levels, transformation may introduce new or magnified effects. DO NOT discharge into sewer or waterways. Ecotoxicity Ingredient portland cement graded sand

Persistence: Water/Soil No Data Available No Data Available

Persistence: Air

Bioaccumulation

Mobility

No Data Available No Data Available

No Data Available No Data Available

No Data Available No Data Available

Section 13 - DISPOSAL CONSIDERATIONS ■ Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws operating in their area. In some areas, certain wastes must be tracked. A Hierarchy of Controls seems to be common - the user should investigate: • Reduction • Reuse • Recycling • Disposal (if all else fails) This material may be recycled if unused, or if it has not been contaminated so as to make it unsuitable for its intended use. Shelf life considerations should also be applied in making decisions of this type. Note that properties of a material may change in use, and recycling or reuse may not always be appropriate. In most instances the supplier of the material should be consulted. • DO NOT allow wash water from cleaning or process equipment to enter drains. • It may be necessary to collect all wash water for treatment before disposal. • In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first. • Where in doubt contact the responsible authority. • Recycle wherever possible or consult manufacturer for recycling options. • Consult State Land Waste Management Authority for disposal. continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 10 of 11 Section 13 - DISPOSAL CONSIDERATIONS

• Bury residue in an authorised landfill. • Recycle containers if possible, or dispose of in an authorised landfill. Section 14 - TRANSPORTATION INFORMATION HAZCHEM: None (ADG7) NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS: ADG7, UN, IATA, IMDG Section 15 - REGULATORY INFORMATION Indications of Danger: Xi

Irritant

POISONS SCHEDULE None REGULATIONS Regulations for ingredients portland cement (CAS: 65997-15-1) is found on the following regulatory lists; "Australia High Volume Industrial Chemical List (HVICL)","Australia Inventory of Chemical Substances (AICS)","OECD List of High Production Volume (HPV) Chemicals"

graded sand (CAS: 14808-60-7) is found on the following regulatory lists; "Australia - New South Wales Hazardous Substances Prohibited for Specific Uses","Australia - New South Wales Hazardous Substances Requiring Health Surveillance","Australia - Queensland Workplace Health and Safety Regulation - Hazardous substances for which health surveillance must be supplied","Australia South Australia - Hazardous Substances Requiring Health Surveillance","Australia - Tasmania Hazardous Substances Requiring Health Surveillance","Australia Western Australia Hazardous Substances Prohibited for Specified Uses or Methods of Handling","Australia - Western Australia Hazardous Substances Requiring Health Surveillance","Australia Australian Safety and Compensation Council (ASCC) Draft National Code of Practice for the Control of Workplace Hazardous Chemicals - Schedule 4 Hazardous chemicals Requiring Health Surveillance","Australia Hazardous Substances","Australia High Volume Industrial Chemical List (HVICL)","Australia Inventory of Chemical Substances (AICS)","Australia Occupational Health and Safety (Commonwealth Employment) (National Standards) Regulations 1994 - Hazardous Substances Requiring Health Surveillance","Australia Work Health and Safety Regulations 2011 - Hazardous chemicals (other than lead) requiring health monitoring","Australia Work Health and Safety Regulations 2011 - Restricted hazardous chemicals","FisherTransport Information", "International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs","International Fragrance Association (IFRA) Survey: Transparency List","OECD List of High Production Volume (HPV) Chemicals","United Nations Consolidated List of Products Whose Consumption and/or Sale Have Been Banned, Withdrawn, Severely Restricted or Not Approved by Governments"

No data for Dunlop AAC Concrete Block Adhesive (CW: 33-7752) Section 16 - OTHER INFORMATION ■ Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using available literature references. A list of reference resources used to assist the committee may be found at: www.chemwatch.net/references. ■ The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available engineering controls must be considered. This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written continued...

DUNLOP AAC CONCRETE BLOCK ADHESIVE Chemwatch Independent Material Safety Data Sheet Issue Date: 6-Dec-2012 A317LP(cs)

permission from CHEMWATCH. TEL (+61 3) 9572 4700. Issue Date: 6-Dec-2012 Print Date: 6-Dec-2012 This is the end of the MSDS.

CHEMWATCH 33-7752 Version No:2.1.1.1 CD 2012/4 Page 11 of 11 Section 16 - OTHER INFORMATION