2993mm WIDE
2179mm DEEP
2300mm HIGH
*ILLUSTRATIONS WITHIN THIS MANUAL ARE FOR INDICATIVE PURPOSES THE APPEARANCE OR PROFILE OF SOME COMPONENTS MAY VARY ANY VARIATIONS HAVE BEEN TESTED FOR THIS PRODUCT, AND WILL NOT PREVENT ITS ASSEMBLY, OR EFFECT ITS FUNCTION
Foundation Requirements THIS PRODUCT IS DESIGNED FOR INSTALLATION ON, AND ANCHORING TO, A CONCRETE SLAB FOUNDATION IT IS RECOMMENDED THAT THE CONCRETE SLAB IS AT LEAST 100mm THICK TO MINIMISE WATER RETENTION, A 75mm WIDE x 25mm DEEP REBATE IS RECOMMENDED AROUND THE PERIMETER OF THE SHED’S FOOTPRINT – REFER TO PAGE 23 FOR DETAILS NOTE THAT THIS REBATE WILL NEED TO BE SET IN AN ADDITIONAL 75mm AT THE FRONT OF THE SHED (AS ILLUSTRATED ON PAGE 23) TO ALLOW FOR THE SLIDING DOOR TRACK UNDULATIONS IN THE FOUNDATION MAY RESULT IN THE MISALIGNMENT OF PANELS, PARTICULARLY THE DOORS – USE SHIMS, PACKERS, OR WEDGES TO COMPENSATE FOR SUCH UNDULATIONS WHERE NECESSARY ALTERNATE FOUNDATIONS, INCLUDING SPECIFICATIONS, ARE THE RESPONSIBILITY OF THE OWNER AND/OR INSTALLER OF THIS PRODUCT IT IS RECOMMENDED THAT ENGINEERING SERVICES ARE ENGAGED FOR FURTHER OR ALTERNATE FOUNDATION SPECIFICATIONS
Tools Required
ELECTRIC DRILL
MALLET
10mm MASONARY DRILL BIT
TAPE MEASURE
ELECTRIC DRILL WITH HAMMER FUNCTION
SHIFTING SPANNER / 13mm SOCKET TOOL
POP RIVET TOOL
10mm DRILL BIT
STEP LADDER (min 1.8m)
Tools Recommended
PHILLIPS HEAD SCREW DRIVER
MARKER
SILICONE
SET OF TRESTLES / SAWHORSES
Safety Notes SOME PARTS AND ASSEMBLIES HAVE SHARP EDGES AND/OR SHARP CORNERS THE USE OF GLOVES AND SAFETY SHOES IS HIGHLY RECOMMENDED PAY ATTENTION TO WHERE THESE PARTS CAN BE HANDLED MOST SAFELY, AND PLAN THE HANDLING OF THESE PARTS AND ASSEMBLIES PRIOR TO WORKING WITH THEM
THE ASSEMBLY OF THIS PRODUCT REQUIRES DRILLING INTO SHEET METAL WHICH PRODUCES SMALL METAL SHAVINGS THE USE OF SAFETY GLASSES, AS WELL AS THE CLEARING OF THESE SHAVINGS THROUGHOUT THE ASSEMBLY PROCESS IS HIGHLY RECOMMENDED
THE ASSEMBLY OF THIS PRODUCT REQUIRES SOME LIFTING OF HEAVY ASSEMBLIES
Assembly Process
STEP ONE: Parts Checklist - Unpack and Check All Parts ............................................................. 4 GUIDE: SNAPTiTE Panel Assembly ..................................................................................................... 7 STEP TWO: Spliced Channel Assembly ............................................................................................ 8 STEP THREE: Spliced Ridge Beam Assembly ................................................................................... 9 STEP FOUR: Roof Panel Construction (2 Required) ...................................................................... 10 STEP FIVE: Rear Wall Construction .................................................................................................. 11 STEP SIX: Side Wall Construction ..................................................................................................... 12 STEP SEVEN: Side Wall Construction (Window) ............................................................................ 13 STEP EIGHT: Front Wall Construction .............................................................................................. 15 STEP NINE: Sliding Door Construction (2x Required) .................................................................... 16 STEP TEN: Wall Assembly .................................................................................................................. 18 STEP ELEVEN: Gable Panel & Door Track Installation .................................................................. 19 STEP TWELVE: Roof Assembly .......................................................................................................... 21 STEP THIRTEEN: Anchoring & Door Installation .............................................................................. 24 Clean Up & Troubleshooting .......................................................................................................... 25
STEP ONE: Parts Checklist - Unpack and Check All Parts
MAIN PACK #2
MAIN PACK #1
PACK
PART NUMBER
QUANTITY
IMAGE
H31
3
SNAPTiTE SHEET - STRAIGHT 2034mm LONG x 773mm WIDE
H30
2
SNAPTiTE SHEET - STRAIGHT 2034mm LONG x 773mm WIDE
HRC
4
SNAPTiTE SHEET - STRAIGHT 2034mm LONG x 731mm WIDE
30222ECP
1
97B-L/R
2
RIDGE BEAM - SPLICED 1152mm LONG
ZARSP
1
RIDGE BEAM JOINER 450mm LONG
ZACO202
2
SLIDING DOOR TOP TRACK 1475mm LONG
95J
2
SLIDING DOOR BOTTOM TRACK 1475mm LONG
13A
2
GABLE PANEL BRACE 393mm LONG - NOTCHED ENDS
INSTPMN30222H
1
ANCHORSET
1
ANCHOR KIT - 8 PACK BRACKETS + BOLTS + NUTS + DYNABOLTS
H25
2
SNAPTiTE SHEET - STRAIGHT 2034mm LONG x 773mm WIDE
H27
2
SNAPTiTE SHEET - STRAIGHT 1989mm LONG x 773mm WIDE
H28
1
SNAPTiTE SHEET - STRAIGHT 1415mm LONG x 773mm WIDE
44L
2
SNAPTiTE SHEET - STRAIGHT 1546mm LONG x 773mm WIDE
44R
2
SNAPTiTE SHEET - STRAIGHT 1546mm LONG x 773mm WIDE
45A
2
SNAPTiTE SHEET - STRAIGHT 1546mm LONG x 773mm WIDE
GSW01
1
GARDEN SHED WINDOW SINGLE 758mm WIDE x 648mm HIGH
16L
2
GABLE PANEL - LEFT 1475mm LONG
16R
2
GABLE PANEL - RIGHT 1475mm LONG
PAGE 5
PAGE 6
DESCRIPTION
SNAPTiTE CHANNEL PACK REFER TO NEXT PAGE
INSTRUCTIONS & FITTINGS PACK REFER TO PAGE AFTER NEXT
PRINTED PART NUMBERS ARE FEATURED ON THE REVERSE SIDE OF SNAPTiTE SHEETS
CHECK
STEP ONE: Parts Checklist - Unpack and Check All Parts PART NUMBER
QUANTITY
IMAGE
DESCRIPTION
13A
1
SNAPTiTE CHANNEL - STRAIGHT 393mm LONG
79W
2
SNAPTiTE CHANNEL - STRAIGHT 716mm LONG
80W
2
SNAPTiTE CHANNEL - NOTCHED 618mm LONG
58C
4
SNAPTiTE CHANNEL - STRAIGHT 773mm LONG
79D
2
SNAPTiTE CHANNEL - STRAIGHT 1445mm LONG
H58L
4
SNAPTiTE CHANNEL - STRAIGHT 1989mm LONG
H80C
2
SNAPTiTE CHANNEL - NOTCHED 2034mm LONG
55GL
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
55GR
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
59XL
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1089.5mm LONG
59XR
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1089.5mm LONG
77BL
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
77BR
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
77XL
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
77XR
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
78BL
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1126.5mm LONG
78BR
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1126.5mm LONG
81BL
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
81BR
1
SPLICED SNAPTiTE CHANNEL - NOTCHED 1496.5mm LONG
81CL
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1126.5mm LONG
81CR
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1126.5mm LONG
81XL
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1089.5mm LONG
81XR
2
SPLICED SNAPTiTE CHANNEL - STRAIGHT 1089.5mm LONG
87B
4
LIP TRIM 1546mm LONG
CHECK
PRINTED PART NUMBERS ARE FEATURED ON THE INSIDE OF SNAPTiTE CHANNELS, LIPS AND JAMBS
STEP ONE: Parts Checklist - Unpack and Check All Parts PART NUMBER
QUANTITY
IMMN30222H
1
ASSEMBLY INSTRUCTION MANUAL
CSJ
12
CHANNEL SPLICE JOINER 200mm LONG
MN14A
2
GABLE END CAP
FAST070
1
SLIDING DOOR LATCH
FAST071
1
SLIDING DOOR RETAINER
BL12B
2
SLIDING DOOR PLATE
OTCO22
4
SLIDING DOOR ROLLER
FAST053
2
SLIDING DOOR STOP
FAST047
4
C HANDLE SCREW
FAST048
2
C HANDLE
BKT261
4
SLIDING DOOR TRACK BRACKET (INTERNAL)
BKT20
2
ANCHOR BRACKET (TYPE: INTERNAL SLIDING DOOR TRACK)
FAST018
2
M10x20mm BOLT & NUT
FAST015
2
DYNABOLT
DRILL
1
3mm DRILL BIT
FAST038
1
DRIVER BIT - PHILLIPS HEAD
BLFAST014
10
WAFER HEAD TEK SCREW 10-16x16 - SELF DRILLING
BLPACK230
1
PACKET
SELF TAPPING SCREW PACK (SEE BELOW FOR DETAIL)
BLPACK60
1
PACKET
POP RIVET PACK (SEE BELOW FOR DETAIL)
BLPACK230
BLFAST001
230
8G x 3/8 SELF TAPPING SCREW
BLPACK60
BLFAST009
60
4-3 BLIND POP RIVET
INSTRUCTIONS & HARDWARE PACK
PACK
IMAGE
DESCRIPTION
CHECK
GUIDE: SNAPTiTE Panel Assembly ABSCO SHEDS FEATURE AN INNOVATIVE ASSEMBLY DESIGN WHICH SIGNIFICANTLY REDUCES THEIR ASSEMBLY TIME AND THE NUMBER OF FASTENERS SNAPTITE IS A SYSTEM OF ATTACHING THE PERIMETER CHANNELS TO THE SHEETING ON EACH OF YOUR SHED’S PANELS SNAPTiTE SHEETING FEATURES ‘SNAPTiTE LUGS’ STAMPED AT BOTH ENDS SNAPTiTE CHANNELS ‘SNAP’ ONTO THESE LUGS, THEREFORE SECURING THE CHANNEL ONTO THE SHEET/S* FOR PANELS WITH MULTIPLE SHEETS, SNAPTITE WORKS BEST ONCE ALL OF THE SHEETS HAVE BEEN SCREWED TOGETHER USING THE PRE-PUNCHED HOLES
SCREW SHEETS TOGETHER** (WHERE APPLICABLE)
ORIENTATE THE SNAPTITE CHANNEL WITH THE SMALL SIDE FACING THE FRONT OF THE SHEET, AND THE LONG SIDE FACING THE BACK OF THE SHEET***
PUSH
PUSH
OPTION 1 - PLACE THE BACK OF THE CHANNEL BEHIND THE SHEET AND WORK ALONG LENGTH OF CHANNEL TO PUSH THE SHEETING RIBS INSIDE THE FRONT OF THE CHANNEL WORK YOUR WAY ALONG THE LENGTH OF THE CHANNEL, FOCUSING ON FITTING 2-3 SHEETING RIBS AT A TIME
OPTION 2 - SLIDING THE CHANNEL ONTOTHE SNAPTITE LUGS IS A USEFUL ALTERNATIVE FOR SHORTER CHANNELS THIS HOWEVER IS NOT RECOMMENDED FOR ‘SPLICED’ CHANNELS DUE TO THE CHANNEL JOINER GETTING CAUGHT ON THE RIBS AND JOINS OF THE SHEETS
PUSH THE CHANNEL OVER THE SNAPTITE LUGS UNTIL THE CHANNEL ‘SNAPS’ ONTO THE SHEET ENSURE THAT ALL SNAPTITE LUGS ARE FITTED INTO THE CHANNEL BEFORE PROCEEDING ANY FURTHER WITH ASSEMBLY *IN MANY CASES, THE CHANNEL IS STILL ABLE TO SLIDE ACROSS THE END OF THE SHEET, SO BE SURE TO CENTRE THE CHANNEL ON THE SHEET/S BEFORE PROCEEDING FURTHER **ENSURE THAT ANY ‘EDGE HOLES’ ARE ORIENTATED TO THE ENDS OF EACH SHEET ASSEMBLY PRIOR TO SCREWING SHEETS TOGETHER YOU MAY OBSERVE UP TO A 3MM DIFFERENCE IN THE ENDS OF THE SHEETS ONCE HOLES ARE ALIGNED THIS TYPICALLY WONT PREVENT THE SUCCESSFUL ASSEMBLY OF THE SHED, HOWEVER IF THE DIFFERENCE IS ANY GREATER, YOU HAVE THE OPTION OF CONTACTING YOUR RESELLER FOR REPLACEMENT PARTS, OR RE-DRILLING THE HOLES IN THE SHEETS TO CREATE A BETTER ALIGNMENT ***VERTICAL CHANNELS ON ABSCO SHED DOORS ARE AN EXCEPTION, WHERE THE LONG EDGE OF THE CHANNEL FACES THE FRONT, AND THE SHORT EDGE FACES THE BACK
STEP TWO: Spliced Channel Assembly CHANNELS OVER 2.1m LONG HAVE BEEN CUT IN HALF TO ALLOW THEM TO FIT INTO THE PACKAGING ASSEMBLY OF THESE CHANNELS IS BEST COMPLETED IMMEDIATELY AFTER CHECKING OFF THE PARTS CHECKLIST *SPLICED CHANNELS FEATURE PRINTED PART NUMBERS AND ARROWS INDICATING THE ‘JOIN END’ OF EACH PIECE **ARRANGE ALL OF YOUR SPLICED CHANNELS IN MATCHING PAIRS PRIOR TO COMMENCING THE ASSEMBLY PROCESS BELOW ***SPLICED CHANNELS FEATURE PAIRS OF PRE-PUNCHED HOLES IN THE ‘JOIN END’ OF EACH CHANNEL AVOID FITTING FASTENERS INTO THESE UNTIL THE FINAL STAGE OF EACH PANEL ASSEMBLY, AS DOING SO PRIOR TO THIS MAY INHIBIT THE FITMENT OF OTHER COMPONENTS***
CHANNELS AND CHANNEL SPLICE JOINERS (CSJ) HAVE A SHORT SIDE (FRONT) AND A LONG SIDE (BACK) PUSH THE CSJ INTO A ‘JOIN END’ OF A SPLICED CHANNEL, AIMING TO POSITION HALF OF THE LENGTH OF THE CSJ INTO THE SPLICED CHANNEL ENSURE THAT THE EDGES OF THE CSJ ‘SNAP’ INTO THE HEMS OF THE CHANNEL
ALIGN THE ‘JOIN END’ OF THE MATCHING SPLICED CHANNEL, AND PUSH THE CSJ INTO THAT CHANNEL AGAIN, ENSURE THAT THE EDGES OF THE CSJ ‘SNAP’ INTO THE HEMS OF THE CHANNEL IF NECESSARY, SLIDE THE SPLICED CHANNELS TOGETHER SO THAT THEY BUTT DIRECTLY INTO ONE ANOTHER
***FIT FASTENERS AS ILLUSTRATED ONLY ONCE THE CHANNEL HAS BEEN ASSEMBLED WITH SHEETING AND OTHER PARTS WHERE APPLICABLE CONFIRM THAT THE ASSEMBLY IS CORRECT BY CHECKING THE PART NUMBERS AND MEASUREMENTS DETAILED BELOW THESE FASTENERS ARE NOT REQUIRED FOR SPLICED CHANNELS THAT NEST INTO RIDGE BEAMS
*AN EXAMPLE OF THE PRINTED PART NUMBER ON AN ‘81A’ SPLICED CHANNEL IS ILLUSTRATED ABOVE **EACH SPLICED CHANNEL FEATURES A ‘LEFT’ AND ‘RIGHT’ PIECE, AND EACH PIECE IS PRINTED WITH THE CHANNEL CODE + ‘L’ OR ‘R’ NOTE THAT THIS DOES NOT NECESSARILY MATCH WITH THE CHANNEL’S ORIENTATION ON THE FINAL ASSEMBLY OF THE SHED ***FOR THE NEATEST FITMENT OF THESE FASTENERS, USE THE PRE-PUNCHED HOLES AT THE ‘JOIN ENDS’ OF THE SPLICED CHANNELS AS A GUIDE TO DRILL MATCHING HOLES THROUGH THE CSJ, SHEETING, AND OTHER PARTS WHERE APPLICABLE USE OF THE DRILL BIT INCLUDED WITH THIS KIT IS RECOMMENDED PRE-PUNCHED HOLES ON THE SHORT SIDE OF THE CHANNEL ALIGN WITH THE EDGE OF THE CSJ, AND WILL NOT RESULT IN COMPLETE CONNECTION THROUGH THE CSJ THIS IS INTENTIONAL, AND WILL NOT BE DETERIMENTAL TO THE FUNCTION OF THESE COMPONENTS ON THIS PRODUCT
STEP THREE: Spliced Ridge Beam Assembly RIDGE BEAMS OVER 2.1m HAVE BEEN CUT INTO SECTIONS TO ALLOW THEM TO FIT INTO THE PACKAGING THE ASSEMBLY OF SPLICED RIDGE BEAMS IS BEST COMPLETED PRIOR TO ERECTING THE WALLS OF YOUR SHED ASSEMBLY OF SPLICED RIDGE BEAMS IS BEST COMPLETED ON A LONG FLAT SURFACE THE USE OF SPACERS IS ALSO RECOMMENDED TO ACHIEVE A STRAIGHT AND SECURE ASSEMBLY SPLICED RIDGE BEAMS ARE ASSEMBLED BY; 1) SLIDING THE ‘JOIN ENDS’* OF EACH PIECE TOGETHER 2) FITTING AND FASTENING THE ‘ZARSP’ RIDGE BEAM JOINER TO THE CENTRE OF THE JOIN *THE ‘JOIN END’ OF SPLICED RIDGE BEAMS FEATURES A SECTION OF ‘CAPPING’ OVERLAPPING THE RIDGE BEAM HAT SECTION
FLIP THE SPLICED RIDGE BEAMS UPSIDE DOWN SO THAT THE ‘CAPPING’ IS FACING DOWN, AND THE ‘HAT SECTION’ IS FACING UP
OVERLAP THE ‘CAPPING’ SLIDE THE ‘CAPPING’ ON ONE PIECE IN BETWEEN THE ‘CAPPING’ AND ‘HAT SECTION’ ON THE OTHER PIECE TO BUTT THE ‘HAT SECTIONS’ DIRECTLY TOGETHER
CHECK THE OVERALL LENGTH OF THE JOINED HAT SECTIONS = 2253mm LONG
POSITION THE ‘ZARSP’ RIDGE BEAM JOINER ON THE CENTRE OF THE JOIN BETWEEN THE TWO ‘HAT SECTIONS’
CAREFULLY FLIP THE ASSEMBLY BACK OVER ONTO THE ‘HAT SECTION’ AND ‘ZARSP’
INSERT 8x FAST014 SCREWS TO SECURE THE ZARSP TO BOTH SECTIONS OF THE SPLICED RIDGE BEAM
PRESS ‘ZARSP’ FIRMLY DOWN INTO THE ‘HAT SECTIONS’ USING A MALLET TO GENTLY TAP INTO PLACE IF NECESSARY
THE CENTRE OF THE ASSEMBLY WILL BE SLIGHTLY PROPPED UP DUE TO THE ‘ZARSP’ - USE SPACERS TO PROP UP THE ENDS
THESE SCREWS ARE TO BE EVENLY SPACED ALONG THE LENGTH OF THE ZARSP AT 60mm OR 2-3/8" CENTRES
STEP FOUR: Roof Panel Construction (2 Required) USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE SCREW SHEETS TOGETHER FIRST, BEFORE FITTING SNAPTiTE CHANNELS CHECK THE ORIENTATION OF ALL SHEETS PRIOR TO FASTENING TOGETHER - ALL PAN HOLES ARE TO BE ON THE SAME END OF THE PANEL ASSEMBLY LAY OUT SHEETS AS ILLUSTRATED, OVERLAPPING EACH BY ONE ‘RIB’ FIT FAST001 SCREWS THROUGH THE PRE-PUNCHED HOLES AS ILLUSTRATED
FIT THE SNAPTiTE CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEETING PAY PARTICULAR ATTENTION TO WHICH SNAPTiTE CHANNEL IS FITTED TO THE END WITH PAN HOLES
FIT THE ROOF PANEL LIP TRIMS USING THE FAST001 SCREWS AS ILLUSTRATED FLIP THE ENTIRE PANEL ASSEMBLY OVER AND FIT FAST001 SCREWS INTO THE SPLICE JOIN HOLES ON THE 81C CHANNEL ONLY THE 78B CHANNEL SLIDES INTO THE RIDGE BEAM REPEAT THE PROCESSES ABOVE FOR THE 2ND ROOF PANEL
STEP FIVE: Rear Wall Construction USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE SCREW SHEETS TOGETHER FIRST, BEFORE FITTING SNAPTiTE CHANNELS CHECK THE ORIENTATION OF THE SHEETS BY CONFIRMING EDGE HOLES ON BOTH SIDES OF THE OVERALL SHEET ASSEMBLY LAY OUT SHEETS AS ILLUSTRATED, OVERLAPPING EACH BY ONE ‘RIB’ FIT FAST001 SCREWS THROUGH THE PRE-PUNCHED HOLES AS ILLUSTRATED
FIT THE SNAPTiTE CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEETING
FIT FAST001 SCREWS INTO THE SPLICE JOIN HOLES FLIP THE ENTIRE PANEL ASSEMBLY OVER AND FIT FAST001 SCREWS INTO THE SPLICE JOIN HOLES ON THE 81B ONLY TIP: STAND THIS PANEL UP SO THAT THE 77B SNAPTiTE CHANNEL IS ON THE TOP OF THIS PANEL THIS IS THE ORIENTATION OF THIS PANEL ON THE FINAL ASSEMBLY
STEP SIX: Side Wall Construction USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE SCREW SHEETS TOGETHER FIRST, BEFORE FITTING SNAPTiTE CHANNELS CHECK THE ORIENTATION OF THE SHEETS BY CONFIRMING EDGE HOLES ON BOTH SIDES OF THE OVERALL SHEET ASSEMBLY LAY OUT SHEETS AS ILLUSTRATED, OVERLAPPING EACH BY ONE ‘RIB’ FIT FAST001 SCREWS THROUGH THE PRE-PUNCHED HOLES AS ILLUSTRATED
FIT THE SNAPTiTE CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEETING
FIT FAST001 SCREWS INTO THE SPLICE JOIN HOLES FLIP THE ENTIRE PANEL ASSEMBLY OVER TO FIT REMAINING FAST001 SCREWS INTO THE SPLICE JOIN HOLES TIP: STAND THIS PANEL UP SO THAT THE 59X SNAPTiTE CHANNEL IS ON THE TOP OF THIS PANEL THIS IS THE ORIENTATION OF THIS PANEL ON THE FINAL ASSEMBLY
STEP SEVEN: Side Wall Construction (Window) USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE SCREW SHEETS TOGETHER FIRST, BEFORE FITTING SNAPTiTE CHANNELS CHECK THE ORIENTATION OF THE SHEETS BY CONFIRMING EDGE HOLES ON BOTH SIDES OF THE OVERALL SHEET ASSEMBLY LAY OUT SHEETS AS ILLUSTRATED, OVERLAPPING EACH BY ONE ‘RIB’ FIT FAST001 SCREWS THROUGH THE PRE-PUNCHED HOLES AS ILLUSTRATED
USE THE 2x TOP HOLES IN H28 AS GUIDES TO DRILL CORRESPONDING HOLES THE HRC SHEETS
FIT THE SNAPTiTE CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEETING FIT THE TOP 79W CHANNEL IN FROM THE REAR OF THE PANEL TO THE 59X CHANNEL USING FAST001 SCREWS ONLY AT THE REAR OF THE SPLICE JOIN
FIT FAST001 SCREW INTO THE SPLICE JOIN HOLES ON THE 81X CHANNEL
2x OPTIONAL 80W CHANNELS ARE PROVIDED FOR COMPLETING THE LINING OF THE PERIMETER OF THE OPENING IN THE SIDE WALL FOR THE WINDOW ALIGN THESE CHANNELS AS ILLUSTRATED, ENSURING THAT THE INSIDE OF EACH OF THEM ARE PRESSED UP FIRMLY TO THEIR RESPECTIVE SHEET
ALTERNATIVELY, THE WINDOW CAN BE FITTED DIRECTLY TO THE SHEETING IN THIS CASE IT IS RECOMMENDED THAT THE TOP EDGE OF THE WINDOW BE SLOTTED UP IN BETWEEN THE 79W AND 59X CHANNELS
USE THE 3mm DRILL BIT SUPPLIED TO DRILL THROUGH THE PRE-PUNCHED HOLE IN THE 80W CHANNELS INTO THE RESPECTIVE SHEETS
USE THE 3mm DRILL BIT TO DRILL 2x HOLES 20mm APART IN THE CENTRE OF, AND 10mm DOWN FROM THE TOP OF THE SECURITY WINDOW THESE HOLES WILL ALIGN WITH THE SPLICE JOIN HOLES IN THE TOP SNAPTiTE CHANNEL REPEAT THIS FOR THE BOTTOM OF THE WINDOW WITH THESE HOLES 20mm ABOVE THE BOTTOM OF THE SECURITY WINDOW DRILL A HOLE ON EITHER SIDE OF THE WINDOW AS ILLUSTRATED - THESE WILL ALIGN WITH THE 80W CHANNEL HOLES FIT FAST001 SCREWS AND FAST009 POP RIVETS AS ILLUSTRATED
NEST THE SECURITY WINDOW INTO THE OPENING CREATED IN THE MIDDLE OF THE PANEL BY THE H31C SHEET USE THE 3mm DRILL BIT TO DRILL THE REMAINING HOLES THROUGH THE SECURITY WINDOW INTO THE SHEETING, AND FIT FAST001 SCREWS AND FAST009 POP RIVETS AS ILLUSTRATED
STEP EIGHT: Front Wall Construction USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE SCREW SHEETS TOGETHER FIRST, BEFORE FITTING SNAPTiTE CHANNELS CHECK THE ORIENTATION OF THE SHEETS BY CONFIRMING EDGE HOLES ON BOTH SIDES OF THE OVERALL SHEET ASSEMBLY LAY OUT SHEETS AND FIT THE SNAPTiTE CHANNELS ONTO THE ENDS OF THE SHEETING AS ILLUSTRATED
NEST THE VERTICAL ‘DOOR OPENING TRIM CHANNELS’ OVER THE SHEETS WITH THE LONG SIDE ON THESE CHANNELS FACING OUTWARDS USE THE HOLES IN THE H80C CHANNELS AS A GUIDE TO DRILL CORRESPONDING HOLES IN THE H25 SHEETS FIT FAST001 SCREWS AS ILLUSTRATED
NEST THE HORIZONTAL ‘DOOR OPENING TRIM CHANNELS’ OVER THE TOP AND BOTTOM SNAPTiTE CHANNELS ALONG THE DOOR OPENING FIT FAST001 SCREWS AS ILLUSTRATED
FLIP OVER THE ENTIRE PANEL AND FIT FAST009 POP RIVETS TO THE BACK OF THE FRONT WALL AS ILLUSTRATED
STEP NINE: Sliding Door Construction (2x Required) USE A SET OF TRESTLES OR SAWHORSES TO CREATE AN ELEVATED WORK SURFACE FIT THE SNAPTiTE CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEET
USE THE HOLES IN THE H58L CHANNELS AS A GUIDE TO DRILL CORRESPONDING HOLES IN THE H27 SHEET
FIT THE VERTICAL CHANNELS ILLUSTRATED ONTO THE ENDS OF THE SHEETING THESE CHANNELS ARE FITTED WITH THE HIGH SIDE FACING FORWARD USE FAT009 POP RIVETS TO FASTEN THESE CHANNELS TO THE SHEET, AS WELL AS THE TOP AND BOTTOM SNAPTiTE CHANNELS USING THE PRE-PUNCHED HOLES TIP: USE THE 3mm DRILL BIT TO DRILL A HOLE INTO THE SHEET THROUGH THE PRE-PUNCHED HOLES WHERE THE TOP/BOTTOM CHANNELS MEET THE VERTICAL CHANNELS
CENTRE THE 12B DOOR PLATE ADJACENT TO THE REMAINING PRE-PUNCHED HOLES IN THE VERTICAL CHANNEL USE THE PRE-PUNCHED HOLES IN THE 12B DOOR PLATE AS A GUIDE TO DRILL HOLES THROUGH THE DOOR SHEET USE FAST001 SCREWS TO FIT THE 12B DOOR PLATE TO THE FRONT OF THE DOOR PANEL AS ILLUSTRATED DRILL 2x HOLES THROUGH THE CENTRE OF VERTICAL CHANNEL FOR THE FAST048 C-HANDLE INSERT THE FAST047 SCREWS IN FROM THE BACK OF THE DOOR PANEL AND THREAD INTO THE FAST048 C-HANDLE AS ILLUSTRATED
FLIP THE PANEL OVER AND FIT FAST009 POP RIVETS TO THE PRE-PUNCHED HOLES IN THE PERIMETER CHANNELS AS ILLUSTRATED
ALIGN 2x OTCO22 DOOR ROLLERS 50mm IN FROM EACH SIDE OF THE DOOR PANEL, AND DRILL CORRESPONDING HOLES IN THE 58C CHANNEL SECURE TO THE 58C CHANNELS USING FAST001 SCREWS REPEAT THE PROCESSES ON THE PREVIOUS PAGE & ABOVE FOR THE 2ND DOOR PANEL USE THE 1ST DOOR PANEL TO CHECK ALIGNMENT OF THE 12B DOOR PLATE AND FAST048 C-HANDLE
USE FAST009 POP RIVETS TO FIT THE FAST070 LATCH TO THE PRE-PUNCHED HOLES ON THE DOOR PLATE AS ILLUSTRATED SLIP THE LEADING EDGE OF THE DOOR PLATES UNDER THE H58L CHANNELS
USE FAST001 POP SCREWS TO FIT THE FAST071 RETAINER TO THE PRE-PUNCHED HOLES ON THE H58L VERTICAL CHANNEL AS ILLUSTRATED ENSURE THAT THE LEADING SCREW PENETRATES THE SHEET AS WELL AS THE DOOR PLATE ENSURE THAT THE LEADING POP RIVET PENETRATES THE SHEET AS WELL AS THE DOOR PLATE CUT 8x 750mm LENGTHS OF THE OTCO23 DOOR BRUSH STRIP (4x FOR EACH DOOR PANEL) PEEL BACK THE ADHESIVE TAPE, AND ADHERE 1x STRIP ON EACH SIDE OF THE 58C SNAPTiTE CHANNELS
STEP TEN: Wall Assembly USE ASSISTANCE, WHETHER THAT BE ANOTHER PERSON, OR A LADDER, TRESTLE OR STRINGLINE TO HOLD THE PANELS UPRIGHT WHILST ADJACENT PANELS CAN BE MOVED INTO POSITION NEST THE TOP AND BOTTOM CHANNELS ON THE SIDE PANELS INTO THE NOTCHED ENDS OF THE TOP AND BOTTOM CHANNELS ON THE FRONT AND REAR WALL PANELS ALIGN THE EDGES HOLES ON EACH OF THE PANELS BEING CONNECTED, AND FIT FAST001 SCREWS AS ILLUSTRATED WHEN FITTING FAST001 SCREWS TO JOIN EDGE HOLES, CHECK FIRST THAT THE WASTE HAS BEEN CLEARED FROM ALL HOLES ON BOTH EDGES USE THE DRILL BIT SUPPLIED TO CLEAR ANY REMAINING WASTE OVERLAP THE EDGE HOLES ON THE FRONT/REAR WALL OVER THOSE ON THE SIDE WALL
AIM THE TIP OF THE SCREW THROUGH THE EDGE HOLE ON THE FRONT/REAR WALL, AND THEN GENTLY MANEAVOUR THE TIP OF THE SCREW TOWARDS THE HOLE BEHIND ONLY ACTIVATE YOUR DRILL ONCE THE TIP OF THE SCREW IS ENGAGED INTO THE HOLE BEHIND
STEP ELEVEN: Gable Panel & Door Track Installation CONNECT A LEFT GABLE PANEL AND A RIGHT GABLE PANEL TOGETHER USING FAST001 SCREWS AS ILLUSTRATED – PLACE THIS ASSEMBLY ASIDE WHILST THE OPPOSITE GABLE ASSEMBLY IS PREPARED
REPEAT THIS FOR THE REMAINING GABLE PANELS
USE ASSISTANCE TO ALIGN THE 1ST GABLE ASSEMBLY ON THE REAR WALL PANEL AND FASTEN USING FAST001 SCREWS AS ILLUSTRATED
REPEAT THE PROCESS ABOVE FOR THE REMAINING GABLE ASSEMBLY ON THE FRONT WALL PANEL, USING FAST009 POP RIVETS INSTEAD OF FAST001 SCREWS ALIGN A TOP DOOR TRACK INTO THE CORRESPONDING GABLE PANEL, AND FASTEN USING 3x FAST009 POP RIVETS AS ILLUSTRATED
REPEAT THE PROCESS ABOVE FOR THE REMAINING TOP DOOR TRACK
PLACE THE 2x 95J HAT SECTIONS TOGETHER, AND THEN NEST THE 13A CHANNEL INTO THE CENTRE OF THE JOIN AS ILLUSTRATED
USE A 3mm DRILL BIT TO DRILL 1x HOLE THROUGH THE SIDE OF A 95J HAT SECTION AND INTO THE 13A CHANNEL FIT A FAST009 POP RIVET TO SECURE THE POSITION OF THE 13A CHANNEL IN ONE HALF OF THE JOIN ENSURE THAT THE 95J HAT SECTIONS ARE BUTTED TOGETHER, AND THEN DRILL A 2ND HOLE THROUGH THE SIDE OF THE OTHER 95J HAT SECTION AND INTO THE 13A CHANNEL FIT ANOTHER FAST009 POP RIVET TO SECURE THE 13A CHANNEL IN THE 2ND HALF OF THE JOIN DRILL HOLES FOR THE REMAINING FAST009 POP RIVETS ILLUSTRATED, AND THEN COMPLETE ASSEMBLY OF THE BOTTOM DOOR TRACK BY FITTING THESE RIVETS
FIT THE BKT261 DOOR TRACK BRACKETS TO THE INSIDE OF THE OF THE TOP AND BOTTOM CHANNELS ON BOTH SIDE WALLS AS ILLUSTRATED
DRILL 2x HOLES IN EACH END OF THE ZACO202 TOP DOOR TRACK USING THE PRE-PUNCHED HOLES IN THE BKT261 DOOR TRACK BRACKETS AS A GUIDE
POSITION THE BOTTOM DOOR TRACK INSIDE THE FRONT WALL PANEL AND SECURE TO THE BKT261 DOOR TRACK BRACKET USING FAST001 SCREWS AS ILLUSTRATED
STEP TWELVE: Roof Assembly INSTALL THE RIDGE BEAM ONTO ONE OF THE ROOF PANELS BY SLIDING THE END FITTED WITH THE 78B CHANNEL UP IN BETWEEN THE RIDGE CAP AND HAT SECTION AS ILLUSTRATED FIT THE FAST001 SCREWS AS ILLUSTRATED
LIFT THIS ASSEMBLY UP ONTO THE ASSEMBLED WALLS, ENSURING THAT THE LIP TRIMS OVERLAP THE GABLE PANELS ON BOTH THE FRONT AND BACK OF THE SHED FIT THE FAST001 SCREWS AS ILLUSTRATED THOSE NOT ILLUSTRATED ARE BEST LEFT FOR AFTER THE 2ND ROOF PANEL IS INSTALLED
LIFT THE 2ND ROOF PANEL UP ONTO THE ASSEMBLED WALLS, AGAIN ENSURING THAT THE END FITTED WITH THE 78B CHANNEL IS ORIENTATED TOWARDS THE RIDGE BEAM, AND THAT THE LIP TRIMS OVERLAP THE GABLE PANELS ON BOTH THE FRONT AND BACK OF THE SHED WORKING FROM INSIDE THE SHED, GENTLY LIFT THE RIDGE BEAM/1ST ROOF PANEL ASSEMBLY SO THAT THE 78B CHANNEL ON THE 2ND ROOF PANEL CAN BE SLID UP IN BETWEEN THE RIDGE CAPPING AND HAT SECTION AS ILLUSTRATED FIT THE FAST001 SCREWS AS ILLUSTRATED IF THIS IS PROOVING DIFFICULT, CHECK THAT SCREWS JOINING THE SHEETING ARE NOT CATCHING ON THE RIDGE CAPPING – REMOVE IF NECESSARY
THE HOLES IN THE PEAK OF THE GABLES WITH THE 2ND HOLES FROM THE ENDS OF THE RIDGE BEAM FIT FAST001 SCREWS INTO THESE HOLES
FIT 3x FAST001 SCREWS INTO THE HOLES IN THE UNDERSIDE OF THE RIDGE BEAM THAT ALIGN WITH THE 2ND ROOF PANEL LEAVE THE HOLE AT THE REAR BLANK FOR FITMENT OF THE 13A GABLE BRACE AS DETAILED BELOW
FOLD THE NOTHCED ENDS OF THE 2x GABLE BRACES AS ILLUSTRATED
FOR THE REAR WALL FIT THE 13A GABLE BRACE TO ONE SIDE OF THE 77B SPLICE JOIN AS ILLUSTRATED ALIGN THE OTHER END OF THIS GABLE BRACE WITH THE PRE PUNCHED HOLE IN THE RIDGE BEAM HAT SECTION, AND SECURE USING FAST001 SCREW
FOR THE FRONT WALL PANEL, ALIGN THE 13A GABLE BRACE UP UNDERNEATH THE RIDGE BEAM HAT SECTION AND SLIGHTLY OFFSET FROM THE JOIN BETWEEN THE 2x ZACO202 TOP DOOR TRACKS USE THE 3mm DRILL BIT TO DRILL HOLES THROUGH THE PRE-PUNCHED HOLES IN THE ENDS OF THE 13A GABLE BRACE INTO THE TOP DOOR TRACK AND RIDGE BEAM HAT SECTION SECURE THE 13A GABLE BRACE USING FAST001 SCREWS AS ILLUSTRATED
FIT FAST001 SCREWS DOWN THROUGH THE ROOF SHEETS INTO THE GABLE PANELS AS ILLUSTRATED
FOLD THE BOTTOM TABS ON THE 14A GABLE CAPS 180° FOLD THE TOP TABS ON THE 14A GABLE CAP 90° SLIDE THE BOTTOM TABS OVER THE BOTTOM OF THE LIP TRIMS ON ONE END OF THE ROOF ASSEMBLY, AND THEN PRESS THE TOP TABS OVER THE TOP OF THE LIP TRIMS SECURE IN PLACE USING FAST001 SCREWS TIP: THE HOLES IN THE TOP TABS SHOULD ALIGN WITH HOLES IN THE TOP OF THE LIP TRIMS. FOR A NEAT FINISH, THE RIDGE CAPPING MAY NEED TO BE DRILLED INLINE WITH THESE HOLES
STEP THIRTEEN: Anchoring & Door Installation IMPORTANT: 2x OF THE ANCHOR LOCATIONS OVERLAP WITH THE BOTTOM DOOR TRACK THESE LOCATIONS NEED TO BE FITTED WITH THE SPECIALTY ANCHOR BRACKETS BEFORE MOVING THE SHED INTO ITS FINAL POSITION WHEN THE SHED IS MOVED INTO ITS FINAL POSITION, THE BOTTOM DOOR TRACK IS TO BE NESTED OVER THESE SPECIALTY ANCHOR BRACKETS AND DYNABOLTS
USE A 10mm MASONARY DRILL BIT FITTED INTO AN ELECTRIC DRILL WITH HAMMER FUNCTION TO DRILL TO ANCHORING HOLES TO A DEPTH OF >50mm
USE THE VERTICAL HOLE IN THE BKT01/BKT20 BRACKETS AS A GUIDE TO DRILL Ø10mm HOLES IN THE WALLS
WITH A NUT ATTACHED TO EACH DYNABOLT, USE A MALLET TO INSERT A DYNABOLT INTO EACH HOLE TIGHTEN THE NUTS TO SECURE EACH DYNABOLT INTO THEIR RESPECTIVE HOLES REMOVE THE NUTS, AND PLACE BKT01/BKT20 BRACKETS AS ILLUSTRATED PLACE AND TIGHTEN THE NUTS BACK ONTO THE DYNABOLTS TO SECURE THE BRACKETS IN POSITION
SECURE THE WALLS TO THE ANCHOR BRACKETS USING THE M10 BOLTS AND NUTS PROVIDED WITH THE SHED SECURELY ANCHORED, THE DOOR PANELS CAN BE FITTED INTO THE DOOR TRACKS WORKING FROM INSIDE THE SHED, TILT THE TOP OF THE DOOR PANELS UP INSIDE THE TOP DOOR TRACK BY DETACHING THE BOTTOM OF THE 13A GABLE BRACE, THE TOP DOOR TRACK IS MORE FLEXIBLE IN THE MIDDLE OF THE DOOR OPENING, ALLOWING THE DOOR PANEL TO BE PUSHED HIGH ENOUGH FOR THE ROLLERS TO CLEAR THE BOTTOM DOOR TRACK
THE OVERALL HEIGHT OF THE DOOR PANELS CAN BE ADJUSTED USING THE ADJUSTMENT FEATURE ON EACH OF THE DOOR ROLLERS
Clean Up & Troubleshooting PHOTOGRAPH THE COMPLETED ASSEMBLY FOR FUTURE REFERENCE REDUCE THE RISK OF CORROSION BY HOSING OR BLOWING THE COMPLETED STRUCTURE TO REMOVE METAL SHAVINGS, PARTICULARLY THOSE FROM ON TOP OF PAINTED SURFACES SOME COMPONENTS ARE BUNDLED TOGETHER TO MINIMISE THE SHIPMENT VOLUME OF THIS PRODUCT, AS WELL AS REDUCE THE MOVEMENT OF COMPONENTS INSIDE THE PACKAGE FOR PARTS THAT ARE PROVING DIFFICULT TO SEPARATE; - GENTLY (BUT FIRMLY) WEDGE A TOOL SUCH AS A FLAT HEAD SCREW DRIVER TO CREATE A SMALL SEPARATION, AND THEN WORK ON GRADUALLY EXPANDING THAT SEPARATION ALONG THE LENGTH OF THE PARTS, OR - WHERE POSSIBLE, HOLD THE PARTS AT BOTH ENDS AND GENTLY TWIST THEM BACK AND FORTH TO GRADUALLY GENERATE A SEPARATION WHERE COMPONENTS AND/OR ASSEMBLIES APPEAR TO NOT BE ALIGNING, REFER TO COMPONENT MEASUREMENTS PROVIDED IN PARTS CHECKLIST MEASUREMENTS ON SOME COMPONENTS MAY VARY UP TO 3mm EITHER SIDE OF MEASUREMENTS NOMINATED ON THE PARTS CHECKLIST, HOWEVER BEING OF A LIGHT GAUGE STEEL CONSTRUCTION, IN MANY CASES THE ASSEMBLY CAN STILL BE COMPLETED SUCCESSFULLY FOR ALL OTHER CASES PLEASE CONTACT YOUR RETAILER OR THE CUSTOMER SERVICE DETAILS ON THE FOLLOWING PAGE TO ARRNAGE REPLACEMENT PARTS* SNAPTiTE PANELS FEATURE LIGHT GAUGE STEEL COMPONENTS THAT MAY NEED TO BE ADJUSTED INTO THE CORRECT POSITION ONCE ASSEMBLED SNAPTiTE CHANNELS ARE DESIGNED TO BE FLUSH WITH THE OUTSIDE EDGES OF THE END SHEETS ON A COMPLETED SNAPTiTE PANEL USE A MALLET TO GENTLY TAP SNAPTiTE CHANNELS INTO POSITION FOR PANELS WITH MULTIPLE SHEETS, SNAPTITE CHANNELS CAN SOMETIMES GET CAUGHT ON SNAPTiTE LUGS, INHIBITING ADJUSTMENT AND POTENTIALLY SQUEEZING THE RIBS OF THE SHEETING SLIGHTLY FLATTER THIS CAN AFFECT THE ALIGNMENT OF SNAPTiTE CHANNELS ENSURE THAT ALL SNAPTiTE LUGS ARE PROPERLY ENGAGED INTO THE HEMS OF THE RESPECTIVE CHANNELS THIS IS NOT A WATER TIGHT STRUCTURE**, AND THEREFORE LOCALISED WATER INGRESS MAY TAKE PLACE IN EXTREME WEATHER CONDITIONS WATER INGRESS IS HIGHLY DEPENDENT UPON THE FOUNDATION TYPE AND QUALITY, ADJACENT TERRAIN AND/OR STRUCTURES, AND DRAINAGE SERVICES AND/OR SURFACE RUNOFF FLOW SEALING WHERE THE SHEETING/CLADDING MEETS THE FOUNDATION AT THE BOTTOM OF THE STRUCTURE IS NOT RECOMMENDED FOR THE ENTIRE PERIMETER OF THE STRUCTURE, AS THIS PROMOTES WATER RETENTION IF A LOCALISED AREA AROUND THIS PERIMETER IS PRONE TO INGRESS, SEALANT CAN BE APPLIED, HOWEVER IT IS RECOMMENDED THAT RUNOFF OF WATER FROM INSIDE THE STRUCTURE IS CONSIDERED PRIOR TO PROCEEDING *MODIFICATIONS SUCH AS TRIMMING DOWN PARTS TO MEASUREMENTS NOMINATED ON THE PARTS CHECKLIST IS WELCOME, AND WILL NOT VOID THE WARRANTY **REFER TO THE WARRANTY AND USAGE GUIDELINES FOR MORE INFORMATION
Warranty & Usage Guidelines THIS PRODUCT IS DESIGNED FOR THE STORAGE OF GENERAL DOMESTIC GARDENING AND HOUSEHOLD MAINTENANCE EQUIPMENT FOR THE PURPOSE OF THIS APPLICATION, STORAGE IS DEFINED AS THE ENCLOSURE AND WEATHER PROTECTION OF SUCH EQUIPMENT FOR THE PURPOSE OF THIS APPLICATION, SUCH EQUIPMENT IS CONSIDERED THAT WHICH IS DESIGNED AND INTENDED FOR OUTDOOR USE, AND MINIMAL DETRIMENT ASSCOATED WITH ISOLATED EXPOSURE TO MOISTURE CONSIDER THE ABOVE, ALONG WITH THE EFFECTS OF EXTREME TEMPERATURES, SUCH AS CONDENSATION, WHEN IDENTIFYING ITEMS FOR STORAGE INSIDE THIS PRODUCT ADDITIONAL STORAGE MEASURES, SUCH AS THE USE OF SHELVING OR PLINTHS, ARE TO BE EMPLOYED FOR ITEMS WHERE PROTECTION FROM EXPOSURE TO MOISTURE IS SIGNIFICANTLY BEYOND THAT OF GENERAL DOMESTIC GARDENING AND HOUSEHOLD MAINTENANCE EQUIPMENT ELEVATED STORAGE IS ESSTENTIAL FOR CORROSIVE SUBSTANCES, OR ITEMS STAINED WITH CORROSIVE SUBSTANCES, STORED WITHIN THIS PRODUCT SO AS TO MINIMISE THE RISK OF SUCH SUBSTANCES COMING INTO PROLONGED CONTACT WITH IT THIS PRODUCT SHOULD BE CHECKED AFTER ALL EXTREME WEATHER EVENTS IN ORDER TO IDENTIFY ANY DAMAGE OR MINOR DEFORMATIONS THAT SHOULD BE ADDRESSED TO MINIMISE THE RISK OF WATER ENTRY OR STRUCTURAL FALIURES DURING SUBSEQUENT WEATHER EVENTS THIS PRODUCT IS NOT DESIGNED TO BE WATER-TIGHT, AND THEREFORE HEAVY RAIN AND/OR HIGH WIND GUSTS MAY RESULT IN LOCALISED WATER INGRESS MOISTURE MAY ALSO ACCUMULATE BY OTHER MEANS SUCH CONDENSATION, SURFACE RUNOFF FROM SURROUNDING TERRAIN, OR THE INHERENT LIMITATIONS OF THE FOUNDATION UPON WHICH THE PRODUCT IS ANCHORED TO - NONE OF WHICH ARE COVERED UNDER THIS WARRANTY THE APPLICATION OF WATER PROOF SEALANTS IS WELCOMED, HOWEVER APPLICATIONS REUSLTING IN WATER RETENTION, SUCH AS SEALING THE ENTIRE PERIMETER OF THE BASE OF THE PRODUCT, IS NOT COVERED UNDER THIS WARRANTY FOUNDATION SPECIFICATIONS AND ANCHORING LOCATIONS HAVE BEEN NOMINATED AS A MINIMUM FOR SECURING THIS PRODUCT IN PLACE ALTERNATIVES MUST BE ARRANGED INDEPENDENTLY, AND THIS WARRANTY MAY ONLY APPLY WHERE SUCH ALTERNATIVES HAVE BEEN SPECIFIED AND APPROVED BY A QUALIFIED PERSON THE STEEL COATING ON THIS PRODUCT WILL NOT RUST, CRACK , FLAKE, PEEL OR BLISTER FOR 30 YEARS FROM THE DATE OF PURCHASE, WHEN INSTALLED WITHIN AUSTRALIA THIS DOES GARAUNTEE DOES NOT APPLY TO THE FASTENERS (SCREWS, BOLTS, NUTS AND RIVETS) OR FITTINGS (PADBOLTS, HASPS, HINGES) INCLUDED WITH THIS PRODUCT THIS GARAUNTEE DOES NOT INCLUDE SURFACE DETERIORATION RESULTING FROM THE SPREADING AND RETENTION OF SWARF (METAL SHAVINGS) PRODUCED DURING THE DRILLING, CUTTING OR GRINDING OF STEEL COMPONENTS DURING OR AFTER THE ASSEMBLY OF THIS PRODUCT THIS GARAUNTEE DOES NOT COVER SURFACE DETERIORATION RESUTLING FROM EXPOSURE TO CORROSIVE SUBSTANCES, DAMP SOIL, OR PROLONGED EXPOSURE TO MOISTURE FROM INADEQUATE DRAINAGE THIS WARRANTY IS LIMITED TO THE REPLACEMENT AND DELIVERY OF DAMAGED OR INCORRECT COMPONENTS INSTALLATION AND/OR LABOUR COSTS ARE NOT COVERED UNDER THIS WARRANTY WARRANTY CLAIMS ARE TO BE ADDRESSED TO: THE CUSTOMER SERVICE MANAGER - ABSCO INDUSTRIES EMAIL:
[email protected] PHONE: 1800-029-701 FAX: (07) 3344-1191
POST: PO BOX 119 ACACIA RIDGE, QUEENSLAND, AUSTRALIA, 4110
ALL WARRANTY CLAIMS ARE TO INCLUDE PHOTOGRAPHS OF DEFECTIVE PARTS AND ASSEMBLIES, THE ENTIRE PRODUCT FROM MULTIPLE ANGLES, ANY SIGNIFICANT AJACENT STRUCTURES AND/OR TERRAIN, AS WELL AS DETAILS OF THE DEFECTS INCLUDING PART NUMBERS AND RELEVANT MEASUREMENTS ADDITIONAL INFORMATION MAY BE REQUESTED AND MUST BE PROVIDED FOR THE WARRANTY CLAIM TO BE CONSIDERED FOR WARRANTY CLAIMS ASSOCIATED WITH DETERIORATION OR WEATHER EVENTS, PHOTOGRAPHS OF THIS PRODUCT IMMEDIATELY AFTER THE COMPLETION OF ASSEMBLY MAY BE REQUESTED, AND WILL ASSIST IN THE ASSESSMENT OF THE CLAIM THIS PRODUCT CAN BE REGISTERED WITHIN 30 DAYS OF PURCHASE @ www.absco.com.au/register_warranty.php WARRANTY CLAIMS FOR UNREGSITERED PURCHASES ARE TO INCLUDE PROOF OF PURCHASE THE CONCESSIONS PROVIDED BY THIS WARRANTY ARE IN ADDITION TO THE RIGHTS AND REMEDIES DEFINED UNDER THE LAW APPLICABLE TO THE SALE OF THIS PRODUCT THIS WARRANTY EXCLUDES ALL OTHER REPRESENTATIONS, GARAUNTEES, OR WARRANTIES, EXPRESSED OR IMPLIED GARAUNTEES WITHIN THIS WARRANTY CANNOT BE EXCLUDED UNDER AUSTRALIAN CONSUMER LAW, AND ARE NOT TRANSFERABLE ENTITLEMENT TO A REPLACEMENT OR REFUND APPLIES TO CASES OF MAJOR FAILURE ENTITLEMENT TO COMPENSATION FOR LOSS OR DAMAGE APPLIES TO CASES OF MAJOR FAILURE ENTITLEMENT TO REPLACEMENT APPLIES TO CASES THAT DO NOT AMOUNT TO MAJOR FAILURE BUT DO CONCERN MANUFACTURING FAULTS BEYOND PRACTICAL TOLERANCES AND QUALITY FOR FURTHER INFORMATION, VISIT http://www.consumerlaw.gov.au
