Function Vanity 900


[PDF]Function Vanity 900https://2ecffd01e1ab3e9383f0-07db7b9624bbdf022e3b5395236d5cf8.ssl.cf4.rackcd...

0 downloads 90 Views 981KB Size

Function Vanity 900 Full Height 40 80

370

200

50

50

Inspire Series

230

300mm Door

300mm Door

kick or legs

600

50

40 80

300mm Door

370

50

300mm Door

650

650

850

850

Side View

850

150

00

300mm Door

650

650

Side View

Inspire Series

50

50

600

850

100 60

150

400

850

100

300mm Door

Inspire Series

Inspire Series

Inspire Series

325

380mm Drawer

900

370

FUNCVAN9 I/N 4843936

850

Mechanisms/Inclusions

Finger-pull handles. Shelf Soft close door/ standard drawer runners 750 Comes with kickboard 520mm and legs Right Hand Door Adjustable white melamine shelf Note: shelf pins are packed in leg box.

325 150

Dimensions

380mm

W 900 x D 370 xDrawer H 850mm

Shelf

380mm Drawer

850

900

W 910 x D 440 x H 900mm

520mm Left Hand Door

380mm Drawer

900

380mm Drawer

520mm Left Hand Door

900 Dimensions PACKAGED

150 900900

Must be installed by a Licensed Plumber Tap and waste pipework to be positioned within 750 cupboard/door cavity Ensure tops and sides are silicone sealed. Detailed installation instructions over page

50

325 380mm Drawer

380mm Drawer

Shelf 850

520mm 520mm Left Hand Door Right Hand Door

150

150

380mm Drawer

380mm Drawer

Shelf 370

Shelf

380mm Drawer

325

850 325

Side View 520mm Right Hand Door

850

650

Shelf

380mm Drawer

150

325

200

50

50

50 380mm Drawer

Top/Basin

310mm Drawer

325

750750

900

Side View

Left Hand Door

Installation Tips

325

325 150

60

Three (3) years (see warranty information440mm over page).

50mm high polymarble top with integrated310mm rectangular basin with Drawer flat base. 750hole options: 1 only. Tap 440mm Includes 40mm plug and waste Left Hand Door 310mm (no overflow) Drawer Tapware sold separately

850

370

750

200

650

500

150

230 200

White gloss polyurethane exterior. Interior:440mm White moisture resistant Right Hand Door melamine

150

150 370

200

Shelf Warranty

325

150

50

50 325

440mm 440mm Right Hand310mm Door Left Hand Door 310mm 80 Drawer Drawer 50

325

40

850

370

Set-out for Licensed Plumber: View 440mm

Right Hand Door

325

150

325

Side

850 850

650

175

310mm Drawer

50

50 310mm Drawer

310mm Drawer

Shelf Cabinet Finish

50

850

The 900mm wide Function vanity is ideal for bathrooms where space is limited, with its 60 Side compact depth of just 370mm. View 370 600 750 It contains generous basin capacity and storage in a single large cupboard and two 310mm drawers. Its full height (option of kickboard or legs) allows existing floor plumbing to beDrawer easily concealed. Clean lines and classic looks ensure it will suit a range of bathrooms – from traditional to 310mm modern. The exterior is white gloss polyurethane with an310mm easy-care polymarble top with Drawer Drawer Shelf Shelf Shelf basin. Shelf integrated 650

600

310mm Drawer

kick or legs

325

kick or175 legs

400

150

175

325

230

150

150

370

200

CIBO DESIGN – WHO ARE WE?

Established in 1994 on Sydney’s northern beaches, CIBO Design has built a solid reputation for its collection of high quality Australiandesigned bathroomware. Specialising in producing innovative bathroom storage solutions, CIBO’s products combine contemporary design and quality craftsmanship with practicality.

Installation Instructions for Licensed installer (plumber/builder)

Function Vanity Delivery/Pick-up & Installation if an item is damaged or imperfect when opened, do not proceed with installation. if a defective item is installed, Cibo is not liable for removal of the item, nor will Cibo accept responsibility to repair or replace the product. Cibo bathroomware should only be installed by a licensed plumber.

Returns & Exchanges Please retain your receipt and contact the ‘Returns and Exchanges’ Desk at the Bunnings store where you purchased the item.

Vanity Unit Installation 1. Remove top from vanity. 2. Using a hole saw, drill holes for water supply pipes, wastes etc. 3. Carefully move cabinet into place. Pack vanity to required height ensuring vanity top is level from side to side and front to back. Packers may be required behind the unit to ensure top is level and to prevent unit from twisting. 4. Once vanity is level, fasten it to the wall using washers around the appropriate fixings ie. screws, bolts (not supplied). It is the installers responsibility to determine what fixing materials are needed. Fixings should be made as high as possible on unit. Top

Wall Back

Washer

Timber Studs

5. Sweep debris from interior of unit. 6. Now replace top ensuring front and ends of top line up with front and ends of unit. This may leave gaps between top and wall. Fix top to vanity with silicone.

7. The unit must be sealed (along the back edge of top and down the sides) against the wall with bathroom quality silicone. The best method of applying silicone is to cut the appropriate sized tip at a 65° angle and to evenly run a bead around the unit ensuring all gaps are filled. Seal around the cabinet with silicone. 8. Spray soapy water on the silicone joint (between the wall and top) to stop silicone sticking to wall, then wipe off excess silicone and soapy water.

9. Pipes can now be connected. DAMAGE MAY OCCUR IF THE PRODUCTS ARE CONSTANTLY EXPOSED TO WATER. SILICONE MUST BE USED TO SEAL ALL JOINS – TOPS, CABINET SIDES AND KICKBOARDS MUST BE SEALED TO PREVENT WATER PENETRATION.

IMPORTANT NOTES: 1. Attaching Vanity Legs:

Door Removal/Replacement

Product Care & Maintenance

(responsibility of the installer) During installation, it is advisable to remove door(s) from cabinet. To do this, unclip all hinges on each door.

We advise that it is the responsibility of the purchaser to ensure the product is installed and maintained appropriately. All materials used are of high quality and care must be taken when cleaning.

To Adjust Leg

The vanity legs are packaged in a brown box inside the vanity carton. Lay vanity cabinet on its back using the packaging to protect it from damage. Attach legs using screws provided, into pre-drilled holes. Lift vanity into place, avoid dragging it as legs can be dislodged. Adjust leg heights until vanity is level and follow vanity installation instructions. 2. Vanities with Kicks: Kick should fit snugly with the floor and may require trimming with an electric planer if floor is not entirely level. Packers may also be required to ensure cabinet is level from left to right as well as front to back. Seal around kick with bathroom quality silicone to avoid water gaining access from floor and/or walls.

To Remove Doors Locate button at back of top hinge and press. Hold base of door and pull forward to disengage top hinge. Repeat with bottom hinge.

Polymarble Best practice is to clean polymarble with a small amount of warm water and a ‘Micro’ cloth. When finished, wipe dry with ‘Micro’ cloth. Never use caustic chemicals, razor blades, putty knives or abrasive pads as they may damage the surface. Cabinets The most effective cleaning method is to use a damp cotton cloth and a mild detergent. Never use an ammonia-based product or any kind of abrasive cleaning product.

To Replace Doors Line up hinges with corresponding hinge plates. At base of hinge is a small metal rod that must be lined up with cradle arms of hinge-plate.

IT IS THE RESPONSIBILITY OF THE INSTALLER TO ADJUST THE DOOR(S) AFTER INSTALLATION.

3. Under no circumstances should vanities and/or tops be tiled into the wall. CIBO vanities and basin/tops must be fitted to finished/completed wall coverings e.g., tile, masonry or other cladding method deemed acceptable, as per the building code (of Australia) 2013. The CIBO Warranty does not cover any vanity and/or top and/or basin that has been tiled ‘into’ a wall i.e., fitting or fixing a vanity to a wall and tiling around it, and/or tiling down and/or around the vanity and top/basin.

Once hinge is in place, push back of hinge down towards the hinge-plate. Hinge will snap down and engage.

1

Door Hinge Adjustment1 (responsibility of the installer) A

Locate the hinges of the door to be adjusted. It may be necessary to adjust all hinges in order to achieve correct alignment.

1

A

B

1. There are two primary screws that can be adjusted to align the door. A. This screw moves the hinge left or right. B Clockwise direction = moves the hinge left Anticlockwise direction = moves the hinge right. (The opposite occurs when the hinge is fitted the other way around)

A

B. This screw moves the hinge in or out. Clockwise direction = moves the hinge towards the vanity Anticlockwise direction = moves the hinge away from the vanity

B

Warranty This product is covered by a three (3) year replacement product warranty. Products which are within 3 years from the date of purchase, found upon inspection by an authorised representative to be defective will be repaired or exchanged with an equivalent product free of charge. Replaced items become CIBO Design’s property. All replacement products will be available for collection without charge to the customer at the nearest Bunnings store to the customer’s location, or elsewhere as agreed with the customer. Warranty for Labour and Spare Parts – One (1) Year The labour for the replacement of products and spare parts to which this warranty applies will be supplied by CIBO Design if the warranty claim is made within one (1) year from the date of purchase.

Spare parts which are within one (1) year from the date of purchase and found upon inspection by an authorised a CIBO Design representative to be defective in construction, material or assembly, will be replaced free of charge. Products found to be faulty more than one (1) year from the date of purchase will be replaced free of charge by CIBO Design. After one (1) year from date of purchase, labour and spare parts costs are the responsibility of the customer. Warranty Conditions This warranty will apply only under all of the following conditions: • The item has been installed by a licensed plumber; • This item has been installed for and subjected to domestic residential use only; • Failure is due to the manufacture of the product; • Proof of purchase (including date

of purchase) is provided; • The installation of the product is in accordance with the instructions provided This warranty does not include faults caused by: • Unsuitable or improper use; • Incorrect installation or installation not in accordance with the instructions provided; • Installation or part installation by the purchaser or any person other than a Licensed Plumber; • Normal wear and tear including water* and natural causes such as sunlight, humidity and other environmental conditions or factors; • Inadequate or complete lack of maintenance; • Chemical, electrochemical or electrical influences; • Harsh detergents or abrasive cleaners used on product finishes *Important note: CIBO Design vanity cabinets are manufactured from Moisture Resistant (MR) materials but are not waterproof. Care must be

taken to dry spillages or leakage of water that may gain access to cabinetry. Accurate sealing of the vanity cabinet and kickboard (where applicable) is vital for proper maintenance of the product and ensuring longevity. Exclusions - To the fullest extent permitted by law, CIBO Design excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage. Warranty Claim Procedure - Please retain your receipt and contact the ‘Returns and Exchanges’ Desk at the Bunnings store where you purchased the product. Warranty claims can also be sent to: CIBO Design, After Sales Service PO Box 7461, Warringah Mall, Brookvale NSW 2100 Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation

for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits to the customer given by this CIBO Design warranty are in addition to any other rights and remedies available to the customer as a consumer under any laws that relate to the goods covered by this CIBO Design warranty. CIBO Design Pty Ltd 1/130 Old Pittwater Road Brookvale NSW Australia Postal: PO Box 7461, Warringah Mall, Brookvale NSW 2100 Tel: (02) 9939 4464 Email: [email protected]