[PDF]Installation Instructions - Rackcdn.comhttps://a89b8e4143ca50438f09-7c1706ba3fabeeda794725d88e4f5e57.ssl.cf2.rackcd...
74 downloads
175 Views
90KB Size
ISL-28 TBTS SERIES D EMERGENCY LIGHTING EQUIPMENT
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1.
CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C. power is supplied to the unit.
2.
CAUTION – This fixture provides more than one power supply output source. To reduce the risk of electrical shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by disconnecting the unit connector.
3.
CAUTION – This is a sealed unit. The integral, high temperature Ni-Cad battery is not replaceable. Replace the entire unit when necessary and recycle or dispose of the nickel-cadmium battery properly.
4.
DO NOT USE OUTDOORS. The ISL-28 is for use with grounded, UL Listed, indoor fixtures except in heated air outlets or hazardous locations.
5.
The ISL-28 requires an unswitched A.C. power source of either 120 or 277 volts. Properly cap the unused A.C. lead.
6.
Do not mount near gas or electric heaters.
7.
The ISL-28 should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
8.
The ISL-28 will cold strike and operate for 90 minutes one 2′ to 4′ T5 or T8 linear lamp.
9.
The ISL-28 is compatible with all A.C. magnetic and electronic ballasts including multiple lamp ballasts with one lamp operating in the emergency mode.
10.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
11.
Do not use this equipment for other than intended use.
12.
Install in accordance with the National Electrical Code and local regulations.
13.
Installation and servicing should be performed by qualified personnel.
14.
Lighting fixture manufacturers, electricians, and end-users need to ensure product system compatability before final installation.
SAVE THESE INSTRUCTIONS
THIS UNIT CONTAINS A RECHARGEABLE NICKELCADMIUM BATTERY. PLEASE RECYCLE OR DISPOSE OF PROPERLY.
INSTALLATION INSTRUCTIONS CAUTION: Before installing, make certain the A.C. power is off and the ISL-28 unit connector is disconnected.
1. LAMPS OPERATED
The ISL-28 can be used with most 2′-4′ lamps. Refer to the chart below for the type of lamp(s) operated and the number of lamps to be operated in emergency mode.
OPTION 1
LAMP TYPE 2 FT T5-T12 Single, Bipin
EMERGENCY OPERATION
*VIOLET LEADS
WIRING DIAGRAMS
One Lamp
Connected
1, 2, 3, 4, 5, 6, 7, 8, 9
4 FT T5(28W) T8-T12 Disconnected 1, 2, 3, 4, 5, 6, 7, 8, 9 One Lamp Single, Bipin *The 6″ violet leads provide the lamp selection option. The unit is shipped from the factory with the leads disconnected and capped. 2
2. MOUNTING THE ISL-28
Remove the ballast channel cover. Mount the ISL-28 in the ballast channel at least 1/2″ away from the A.C. ballast(s).
When battery packs are remote mounted, the remote distance can not exceed 1/2 of the distance from ballast to lamp specified by the A.C. ballast manufacturer. For example, if the A.C. ballast manufacturer recommends no more than 25′ remote distance, then the battery pack should not exceed 121/2′. Under no circumstances should the battery pack exceed a distance of 50′ from the lamp.
3. WIRING Refer to the wiring diagrams on the back page for the appropriate wiring of lamp(s) and ballast. Install in accordance with the National Electrical Code and local regulations. For additional wiring diagrams consult Customer Service.
4. INSTALLING THE THREADED BODY TEST SWITCH (TBTS) Recessed Troffer Fixture – Select a convenient location with proper clearance in the ballast cover and drill or punch a 7/8″ hole (1/2″ knockout). Insert the 7/8″ bushing into the hole. Push the plastic tube through the bushing. Route the leads of the TBTS through the plastic tube. Connect the LED wires from the unit to the TBTS (Red/Black or Red w/tag to Red, White/Red to White). Push the entire assembly back into the tube until the lens collar rests against the plastic tube. The plastic tube should be adjusted so that the TBTS is within ¼″ of the fixture lens. The TBTS must be visible after installation. Refer to Illustration 1. Linear Fixture – Select a convenient location on the fixture so the TBTS can be seen after installation. Allow for proper clearance inside the fixture and drill or punch a 1/2″ hole. Remove the nut from the TBTS. Push the TBTS housing into the 1/2″ hole and secure with the nut. Connect the LED wires from the unit to the TBTS (Red/Black or Red w/tag to Red, White/Red to White). Refer to Illustration 2.
Illustration 1
Illustration 2 Recessed Troffer Fixture
Linear Fixture FIXTURE TBTS
FIXTURE BALLAST CHANNEL COVER
ISL-28 PLASTIC TUBE
WHITE LEAD
7/8" BUSHING TBTS
ISL-28 FIXTURE LENS
+ RED LEAD
OBSERVE PROPER POLARITY
Page 2
5. WIRING THE A.C. INPUT A. The ISL-28 and A.C. ballast must be on the same branch circuit. B. The ISL-28 requires an unswitched A.C. power source of either 120 or 277 volts. Select the proper voltage lead and cap the unused lead. C. When the ISL-28 is used with a switched fixture, the A.C. input to the ISL-28 must be connected ahead of the fixture switch. Refer to Illustration 3 for switched and unswitched fixture wiring diagrams.
6. BALLAST WIRING BLOCK DIAGRAM Illustration 3
Switched Fixture
Unswitched Fixture
BLACK
WALL SWITCH
WHITE
BLACK
A.C. BALLAST
WHITE HOT A.C. LINE
HOT A.C. LINE
➀
WHT/BLK
WHT/BLK
(277V) ORG
(277V) ORG
(120V) BLK WHT
COMMON WHT
TBTS
A.C. BALLAST
WHT/RED
(+) RED
➀
ISL-28 TBTS
WHT
➀ Select proper voltage lead. Cap unused lead.
ISL-28
WHT/RED
(+) RED
(+) RED/BLK OR RED W/TAG
(120V) BLK WHT
COMMON
(+) RED/BLK OR RED W/TAG
➀ Select proper voltage lead. Cap unused lead.
6. LABELS Attach the appropriate labels adjacent to the TBTS. Annotate Re-lamping label for lamp type and wattage. The Caution and the Re-lamping labels must be on the fixture in a readily visible location to anyone attempting to service the fixture.
7. COMPLETING INSTALLATION When the installation is complete, switch the A.C. power on and join the ISL-28 unit connector.
OPERATION Normal Mode – A.C. power is present. The A.C. ballast operates the fluorescent lamp(s) as intended. The ISL-28 is in the standby charging mode. The TBTS will be lit providing a visual indication that the battery is being charged. Emergency Mode – The A.C. power fails. The ISL-28 senses the A.C. power failure and automatically switches to the Emergency Mode. One lamp is illuminated, at reduced output, for a minimum of 90 minutes. When the A.C. power is restored, the ISL-28 switches the system back to the Normal Mode and resumes battery charging. See page 1 of the Instruction Manual.
TESTING & MAINTENANCE Pressing the red lens on the TBTS turns off the light on the TBTS and forces the unit into emergency mode, interrupting power to the designated A.C. ballast. The emergency lamp is now being lit by the ISL-28 unit. After releasing the TBTS, the fixture returns to normal operation after a momentary delay. To simulate a “BLACK OUT” use the circuit breaker to turn off A.C. power. Initial Testing – Allow the unit to charge approximately 1 hour, then press the TBTS to conduct a short discharge test. Allow a 24 hour charge before conducting a one hour test. The ISL-28 is a maintenance free unit, however, periodic inspection and testing is required. NFPA 101, Life Safety Code, outlines the following schedule: Monthly – Insure that the TBTS is illuminated. Conduct a 30 second discharge test by depressing the TBTS. One lamp should operate at reduced output. Annually – Insure that the TBTS is illuminated. Conduct a full 11/2 hour discharge test. The unit should operate as intended for the duration of the test. “Written records of testing shall be kept by the owner for inspection by the authority having jurisdiction.”
SERVICING SHOULD BE PERFORMED BY QUALIFIED PERSONNEL. Consult Customer Service or visit www.iotaengineering.com for current warranty information. Page 3
TYPICAL WIRING DIAGRAMS For wiring diagrams of ballasts not shown, consult our Customer Service.
TBTS TBTS / CHARGE INDICATOR
COMMON
➃
*AC / EMERGENCY
2. TWO LAMP RAPID START BALLAST
➂
TBTS TBTS / CHARGE INDICATOR
➃
COMMON *AC / EMERGENCY
➁ UNIT CONNECTOR
*LAMP LAMP
➀ ➁ ➂
TBTSTBTS / CHARGE INDICATOR COMMON
➃
*AC / EMERGENCY
COMMON
EMERGENCY ISL-28 BALLAST
➁ UNIT CONNECTOR
LAMP
BLK (120V) WHITE WHT/BLK
➂
LAMP TBTSTBTS / CHARGE INDICATOR
*LAMP COMMON *AC / EMERGENCY
Rev. 042407 68428-390
VIOLET
A.C. Ballast
➀ ➁ ➂ ➃
➀ UNSWITCHED
A.C. Ballast
➃ BLUE
LAMP
VIOLET
VIOLET
WHT/RED
ORG (277V)
EMERGENCY ISL-28 BALLAST
➀ UNSWITCHED
BLK (120V) WHITE
COMMON
WHT/BLK
➁ UNIT CONNECTOR
*LAMP
➂
➀ ➁ ➂
➄
TBTS TBTS / CHARGE INDICATOR
COMMON
➃
*AC / EMERGENCY
➄
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD. DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS. CONNECT BLU/WHT AND RED/WHT WIRES TOGETHER
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
9. THREE LAMP INSTANT START BALLAST BLACK WHITE RED
BLUE
A.C. Ballast
BLUE BLUE
➃
BLUE BLUE/WHT RED/WHT RED YELLOW
SWITCHED OR UNSWITCHED LINE ORG (277V)
EMERGENCY ISL-28 BALLAST
➁ UNIT CONNECTOR
LAMP *LAMP
➂
COMMON
➀ SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
➁ DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED.
➂ LAMP SELECTOR LEADS—REFER
TBTSTBTS / CHARGE INDICATOR
COMMON
➀ UNSWITCHED
BLK (120V) WHITE WHT/BLK
➃
*AC / EMERGENCY
TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS. CONNECT BLU/WHT AND RED/WHT WIRES TOGETHER
➄ TEST ACCESSORY LEADS-
REFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
10. FOUR LAMP INSTANT START BALLAST BLACK WHITE YELLOW
COMMON
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS. CONNECT BLU/WHT AND RED/WHT WIRES TOGETHER
SWITCHED OR UNSWITCHED LINE
BLUE BLUE/WHT RED/WHT RED YELLOW
VIOLET
BLUE
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
ORG (277V)
RED OR RED/BLK (+) VIOLET
BLUE BLUE BLU/WHT BLU/WHT
BLUE BLUE/WHT RED/WHT RED YELLOW
WHT/RED
WHITE
RED RED ORANGE ORANGE YELLOW YELLOW BROWN BROWN
BLACK WHITE
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
SWITCHED OR UNSWITCHED LINE
COMMON SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
8. TWO LAMP INSTANT START BALLAST
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
5. THREE LAMP RAPID START BALLAST BLACK
➃
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
➀ UNSWITCHED
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
5 TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
LAMP
➂
➃
➂
TBTS TBTS / CHARGE INDICATOR
COMMON
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
BLK (120V) WHITE WHT/BLK
VIOLET
LAMP
EMERGENCY BALLAST ISL-28 VIOLET
RED RED
➁
➂
*AC / EMERGENCY
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
ORG (277V)
RED OR RED/BLK (+)
A.C. Ballast
BLUE BLUE/WHT RED/WHT RED YELLOW
BLUE/WHT BLUE/WHT
➀
5
COMMON
SWITCHED OR UNSWITCHED LINE
WHT/RED
BLACK WHITE BLUE BLUE YELLOW YELLOW
➁ UNIT CONNECTOR
*LAMP
RED
4. THREE LAMP RAPID START BALLAST
LAMP SELECTION LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS.
➀ UNSWITCHED
BLK (120V) WHITE WHT/BLK
VIOLET
➂
EMERGENCY ISL-28 BALLAST
YELLOW
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
A.C. Ballast
BLUE BLUE RED RED
LAMP LAMP
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED.
➃
BLUE BLUE/WHT RED/WHT RED YELLOW
EMERGENCY
*LAMP
BLK (120V) WHITE WHT/BLK
BALLAST ISL-28
➁ UNIT CONNECTOR
LAMP
LAMP SELECTION LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS.
SWITCHED OR UNSWITCHED LINE ORG (277V)
➄
➂
VIOLET
➁
➃
ORG (277V)
VIOLET
➃
➀
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED.
SWITCHED OR UNSWITCHED LINE
BLUE BLUE/WHT RED/WHT RED YELLOW
VIOLET
➀ UNSWITCHED
BLK (120V) WHITE WHT/BLK VIOLET
➁ UNIT CONNECTOR
*LAMP
RED OR RED/BLK (+) VIOLET
LAMP
ISL-28
A.C. Ballast
RED
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
ORG (277V)
EMERGENCY BALLAST
BLACK
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
SWITCHED OR UNSWITCHED LINE
WHT/RED
BLUE BLUE/WHT RED/WHT RED YELLOW
BLUE
RED OR RED/BLK (+)
➃
COMMON
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
7. ONE LAMP INSTANT START BALLAST WHITE
COMMON
3. TWO LAMP RAPID START BALLAST
YELLOW YELLOW
➃
COMMON
RED OR RED/BLK (+)
➂
*AC / EMERGENCY
RED RED
➂
*AC / EMERGENCY
RED OR RED/BLK (+)
➁
TBTS TBTS / CHARGE INDICATOR
BLUE BLUE
➁
➂
RED OR RED/BLK (+) VIOLET
➀
➂
COMMON
A.C. Ballast
➀
TBTSTBTS / CHARGE INDICATOR
WHT/RED
➀ UNSWITCHED
BLK (120V) WHITE WHT/BLK
➃
BLACK WHITE
BLK (120V) WHITE WHT/BLK
LAMP *LAMP
WHT/RED
➁ UNIT CONNECTOR
*LAMP
CONNECTOR
WHT/RED
LAMP
EMERGENCY BALLAST ISL-28
VIOLET
RED RED
ORG (277V)
VIOLET
A.C. Ballast
YELLOW YELLOW
BLUE BLUE/WHT RED/WHT RED YELLOW
WHT/RED
BLUE BLUE
ISL-28
SWITCHED OR UNSWITCHED LINE
RED OR RED/BLK (+)
BLACK WHITE
EMERGENCY BALLAST
LAMP
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
➀ UNSWITCHED
ORG (277V)
➁ UNIT
LAMP
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
➂
➃
A.C. Ballast
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
➁
➂
BLU/WHT ORG ORG
SWITCHED OR UNSWITCHED LINE
BLUE BLUE/WHT RED/WHT RED YELLOW
VIOLET
VIOLET
➀
COMMON
WHITE BLU/WHT
YELLOW YELLOW BROWN BROWN BLUE BLUE RED RED
WHT/RED
BLK (120V) WHITE WHT/BLK
VIOLET
➁ UNIT CONNECTOR
*LAMP
UNSWITCHED
EMERGENCY ISL-28 BALLAST
BLACK
➀
ORG (277V)
RED OR RED/BLK (+)
A.C. Ballast
RED RED
BLUE BLUE/WHT RED/WHT RED YELLOW
BLUE BLUE
WHT/RED
BLACK WHITE
6. FOUR LAMP RAPID START BALLAST
SWITCHED OR UNSWITCHED LINE
RED OR RED/BLK (+) VIOLET
1. ONE LAMP RAPID START BALLAST
➀ ➁ ➂
TBTS
TBTS / CHARGE INDICATOR
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
COMMON *AC / EMERGENCY
Page 4
➃ ➄
➀ UNSWITCHED COMMON
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD. DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMP OPERATION SECTION FOR VARIOUS OPTIONS. CONNECT BLU/WHT AND RED/WHT WIRES TOGETHER
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
TYPICAL WIRING DIAGRAMS For Osram/Sylvania Rapid Start Ballasts For wiring diagrams of ballasts not shown, consult our Customer Service.
➂
TBTS/CHARGE TBTS INDICATOR
COMMON
➃
*AC / EMERGENCY
LAMP
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
LAMP *LAMP
ORG (277V)
ISL-28 EMERGENCY BALLAST
➁ UNIT CONNECTOR
➃
TBTS TBTS / CHARGE INDICATOR COMMON *AC / EMERGENCY
Rev. 042407 68428-390
BLK (120V) WHITE WHT/BLK
VIOLET
BLUE BLUE
RED OR RED/BLK (+) VIOLET
A.C. Ballast
BLUE BLUE/WHT RED/WHT RED YELLOW
➂
➁ ➂ ➃
➂
TBTS TBTS / CHARGE INDICATOR
COMMON
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
➁
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
➂ ➃
COMMON *AC / EMERGENCY
BLACK WHITE RED RED YELLOW YELLOW
➀ UNSWITCHED COMMON
A.C. Ballast
BLUE/WHT BLUE/WHT BLUE BLUE
BLUE BLUE/WHT RED/WHT RED YELLOW
LAMP
➀
➃
➀
➀ UNSWITCHED
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
4. THREE LAMP RAPID START BALLAST
SWITCHED OR UNSWITCHED LINE
WHT/RED
YELLOW YELLOW
RED RED
BLK (120V) WHITE WHT/BLK
EMERGENCY ISL-28 BALLAST
➁ UNIT CONNECTOR
*LAMP
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
2. TWO LAMP RAPID START BALLAST BLACK WHITE
BLUE BLUE
VIOLET
COMMON
A.C. Ballast
RED OR RED/BLK (+) VIOLET
➁
YELLOW YELLOW
SWITCHED OR UNSWITCHED LINE ORG (277V)
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD.
LAMP
Page Insert 5
EMERGENCY BALLAST
BLK (120V) WHITE WHT/BLK
➃
TBTSTBTS / CHARGE INDICATOR
➂
➀ ➁ ➂
COMMON *AC / EMERGENCY
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.
ISL-28
➁ UNIT CONNECTOR
*LAMP
DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
SWITCHED OR UNSWITCHED LINE ORG (277V)
VIOLET
➃
➂
➀
➀ UNSWITCHED
BLUE BLUE/WHT RED/WHT RED YELLOW
VIOLET
➁ UNIT CONNECTOR
BLK (120V) WHITE WHT/BLK
RED RED
RED OR RED/BLK (+)
EMERGENCY BALLAST
BLACK WHITE
WHT/RED
ISL-28
VIOLET
*LAMP
ORG (277V)
VIOLET
BLUE BLUE/WHT RED/WHT RED YELLOW
WHT/RED
A.C. Ballast
BLUE BLUE
RED RED
RED OR RED/BLK (+)
BLACK WHITE
3 TWO LAMP RAPID START BALLAST
SWITCHED OR UNSWITCHED LINE
WHT/RED
1. ONE LAMP RAPID START BALLAST
➃
➀ UNSWITCHED COMMON
SELECT PROPER VOLTAGE LEAD. CAP UNUSED LEAD. DO NOT MATE CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED. LAMP SELECTOR LEADS—REFER TO INSTALLATION INSTRUCTIONS, LAMPS OPERATION SECTION FOR VARIOUS OPTIONS
TEST ACCESSORY LEADSREFER TO INSTALLATION INSTRUCTIONS FOR PROPER POLARITY WIRING.