Instruction Manual - K1058V2 April 2016
Linergy LED
Instruction Leaflet K1058V2
IMPORTANT NOTE: Luminaire battery MUST NOT be connected until building has a permanent un-switched live supply. Repeated full discharges caused by fully removing power to luminaires with connected batteries (i.e. a nightly building power down prior to hand over) will permanently damage the battery and invalidate any warranty. Do not touch reflectors during install . Safe Operation 1. Check the rating label for voltage and frequency before connecting this luminaire to the electrical supply. 2. Ensure that the mains supply is switched off when working on this luminaire, whether installing or carrying out any other servicing. 3. Do not mount luminaire on or close to readily flammable materials. 4. To prevent damage to driver, do not mix with conventional magnetic ballasts on the same electrical circuit. 5. Where use in more onerous situations is required, e.g. In part-completed buildings before “drying-out” is completed, or areas where ambient temperatures are outside the normal temperature range, then consult our Sales Office. 6. The light output of the product may cause injuries to human eyes in circumstances where the product is viewed directly with unshielded eyes for more than a few seconds.
April 2016 IP20
Linergy LED Product luminaires comply with EN60598 and are suitable for use in normal interior conditions. o o This luminaire has an ambient temperature range of -10 C to 25 C for the non-emergency version For Emergency variants - This luminaire has an ambient temperature range of 5 C to 25 C, to ensure the batteries work correctly
1
Dimensions H W
L
Fixing Dimensions
Servicing and Disposal 1. At commissioning and handing over of installation ensure that a copy of these instructions is presented to the authority responsible for the operation and maintenance of the luminaries. 2. Servicing, e.g. cleaning, must only be carried out after the electricity supply has been switched off. It must not be assumed that luminaries with lamps not lit are switched off-always check before servicing. 3. Cleaning should be carried out at regular intervals to ensure that dirt does not accumulate to an extent that will impair the thermal safety or optical performance of the luminaire. Regular cleaning will also ensure that the optical performance of the luminaries is maintained. 4. Avoid touching the LED array surface. To clean - Blow surface with either dry air or nitrogen gas. 5. At the end of life the luminaire is classed as WEEE under directive 2002/96/EC and should be disposed of in accordance with local legislation.
A B
C
Luminaire Service
Luminaire Cleaning
Chain/Wire Suspension Fixing Detail
VERSION 4ft 6ft
End of Life and Components Disposal
2 WEEE
M6 Nutserts
D
21.0mm Holes & Besa feature. L W 1142 354 1704 354
H A B C D 72 1120 600 282 646 72 1690 1200 282 1246
Terminal Block Flap / Wiring Configuration Ensure mains supply is switched off and wire terminal block on geartray as per below: LUMINAIRE MUST BE EARTHED
Mains
N - Blue (Neutral) - Green/Yellow (Earth) L - Brown (Switched) Live
Emergency N - Blue (Neutral) - Green/Yellow (Earth) L - Brown (Switched) Live L2 - (Unswitched) Live
To open terminal block flap, loosen screw, push flap to the side.
Eaton Wheatley Hall Road, Doncaster, South Yorkshire, DN2 4NB Sales
General
International Sales
T: +44 (0)1302 303303 F: +44 (0)1302 367155 E:
[email protected]
+44 (0)1302 321541 +44 (0)1302 303220
[email protected]
+44 (0)1302 303250 +44 (0)1302 303251
[email protected]
K1058V2
Open terminal block flap and wire in the correct configuration, as shown on the right. Connect battery leads for emergency fittings only
NOTE FOR EMERGENCY FITTINGS - Connect battery lead
DSI/DALI Dimming: Where applicable a 2 way terminal is provided in the luminaire geartray. Please see additonal leaflet for details.
Linergy LED Accessories Installation 1. Remove two fixing screws from each rear bracket then fit both brackets to rear of housing as shown below. 2. Retain each bracket with two M6 fixing screws & lockwashers. 3. Mechanically fit the luminaire into the installation. 4. Refer to product instructions for wiring
Wireguard Installation 15. Bend the four tabs on the rear of the housing up to approx 90 degs. 16. Hook two of the brackets over the tabs & secure with M6 screws & lockwashers allowing the guard to hang down. 17. Swing the guard up to the luminaire then rotate the remaining two brackets over the tabs, secure with M6 screws & lockwashers.
b
Fixing Rear Brackets
Wireguard Tabs
Fit rear brackets into slots (a), secure using lockwasher and M6 screws (b)
Bend up 4 x tabs approx. 90o
a
SAFETY NOTICE:All 4 screws to be fully tightened
Fitting Wireguard
Bracket Fixing Options
21.0mm
Holes (Lighting trunking etc)
Safety Chain/Wire tabs 4ft = 621.6mm/6ft = 1221.6mm Drop Rods 4ft = 600mm/6ft = 1200mm
Attach 2 brackets on one side of fitting; retain with 2 x M6 screws and lockwashers (a) Swing guard up to other side of fitting, swing 2 brackets over remaining 2 tabs; retain with 2 x M6 screws and lockwashers (b)
100.0
a
b Wireguard fixing tabs
SAFETY NOTICE:Wireguard fixing tabs must not be used for suspending the luminaire
4ft = 646mm/6ft = 1246mm
M6 Nutserts (To suit trunking brackets etc)