Wireless


[PDF]Wireless - Rackcdn.com5e8a560a7cef9ef3dc90-bb2ad470ea539c5163aaf64511d96f64.r56.cf1.rackcdn.com/...

0 downloads 191 Views 2MB Size

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Dimmer with Pico® Remote Controls

1

3

Identify existing wiring Location 1

Location 2

Choose a location for your CasétaTM Wireless dimmer

NOTE: There will be two different types of existing switches in this application. Locations 1 and 3 will use 3-way switches (three screws which control the lights, plus one ground screw) and Location 2 will use a 4-way switch (four screws which control the lights, plus one ground screw). For easiest installation, we recommend replacing one of the 3-way switches with your dimmer (Locations 1 or 3). In this example, we will use Location 1.

Location 3

Three or more switches control the lights (multi-location installation)

Important note: - If one switch controls the lights (single-pole installation) See quick-start guide that came with your dimmer - If two switches control the lights (3-way installation) See page 2 for details

2

3-Way Switch Locations 1 and 3

4

4-Way Switch Location 2

Turn power off at circuit breaker

What you need for a multi-location installation

+

+

In-wall dimmer

Claro® Wallplate

PD-6WCL or P-PKG1W

CW-1

WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit breaker before installing the unit.

5

Remove existing switch from wall at Location 1

Location 1

Two Pico® remote controls with wall-mounting kit PJ2-WALL

13

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Dimmer with Pico® Remote Controls

6

8

Tag and disconnect wires from the existing switch

Location 1

Connect the CasétaTM Wireless dimmer

Location 1

Tagged wire

Place tag - to identify wire on different color screw

Ground (Green / Bare Copper)

7

Different Color Screw

Ground (Green / Bare Copper)

Remove side sections (if necessary)

When installing more than one CasétaTM Wireless dimmer in the same wallbox, it is necessary to remove inner side sections prior to wiring (see image below). See below for derating information.

9

Mount the CasétaTM Wireless dimmer

Location 1

Do not remove outside side sections on dimmers at the end of gang.

Each dimmer has inside side sections removed.

Dimmer in middle has all side sections removed.

Important note:

10

Removing side sections reduces the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.

Location 1

Attach the wallplate

‘snap’ B

A

B

B

C

B

Incandescent/Halogen Total Wattage

CFL/LED Total Wattage

A

B

C

0W 1 W – 25 W

+ 600 W + 500 W

500 W 400 W

400 W 300 W

26 W – 50 W 51 W – 75 W 76 W – 100 W 101 W – 125 W 126 W – 150 W

+ + + + +

300 W 200 W 100 W 50 W 0W

200 W 100 W 50 W 0W 0W

400 W 300 W 200 W 100 W 0W

Wallplate Adapter

14

Wallplate

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Dimmer with Pico® Remote Controls

11

14

Remove existing switch from wall at Location 2

Attach the wallplate bracket and Pico® remote control

Location 2 Location 2

15 12

Tag and disconnect wires from the existing switch

Attach the wallplate

Location 2

‘snap’

Location 2

Place tags - to identify wires on different color screws

Wallplate Adapter

Different Color Screws

13

16

Ground (Green / Bare Copper)

Remove existing switch from wall at Location 3

Location 3

Connect the wires

Location 2

Tagged Wires

Ground (Green / Bare Copper)

15

Wallplate

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Dimmer with Pico® Remote Controls

17

21

Tag and disconnect wires from the switch

Turn power on at circuit breaker

Place tag - to identify wire on different color screw

Location 3

Pairing the dimmer and PicoR remote controls Ground (Green / Bare Copper)

18

Different Color Screw

22

Press and hold "Off" button on dimmer

Connect the wires Location 1

Tagged Wire 0

HOLD

5 10

UNTIL

15

6 sec. Location 3

Status LEDs flash

Ground (Green / Bare Copper)

19

Attach the wallplate bracket and Pico® remote control

23

Location 3

Press and hold "Off" button on remote control

Location 2

HOLD 0

UNTIL

5

3x

10 15

6 sec.

20

Lights flash three times

Attach the wallplate

Location 3

‘snap’

24

Repeat for remote control at Location 3

Repeat steps 22 and 23 to pair remote control at Location 3. Wallplate Adapter

Wallplate

16

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Dimmer with Pico® Remote Controls Schematic Diagram Location 1

Location 2

Traveller

Traveller

Line / Hot

CasétaTM Wireless Dimmer *

Traveller

Location 3

Pico® Remote Control

Traveller

Pico® Remote Control

Load

Ground

Neutral

Tagged Wire

Tagged Wires

* It is recommended to install dimmer in either Location 1 or 3.

17

0301710b 07/2014

Wireless Multi-Location Installation - CasétaTM Wireless In-Wall Switch with Pico® Remote Controls Schematic Diagram Location 1

Location 2

Location 3

Traveller

Traveller Black Blue

Line / Hot

Black

CasétaTM Wireless Switch *

Traveller

Pico® Remote Control

Traveller

Pico® Remote Control

Load

Ground (Green)

Neutral

Tagged Wire

Tagged Wires

* It is recommended to install switch in either Location 1 or 3.

22

0301710b 07/2014

Wireless Adjusting Low-End Trim on a CasétaTM Wireless In-Wall Dimmer

2

Adjust (continued)

b.

On

TAP

Brighter UNTIL

Darker Off

Light stops flickering and is stable

In-wall dimmer

3 Adjusting Low-End Trim -

HOLD

To optimize performance of CFL / LED lamps

1

Save

Enter

HOLD

UNTIL

Status LED stops flashing

0

5 10

UNTIL

15

6 sec.

4

A status LED starts flashing

2

Verify

a.

a. Tap "Off" one time. Light will turn off. b. Tap "Brighter" one time. Light will turn on.

Adjust

c. If light is still off or is flickering, repeat steps 1-4.

a.

HOLD Hold

UNTIL b.

Light stops dimming or turns off

b.

23

0301710b 07/2014

Wireless Adjusting High-End Trim on a CasétaTM Wireless In-Wall Dimmer

2

Adjust (continued)

b. On

TAP

Brighter UNTIL

Darker Off

Desired light level is achieved In-wall dimmer

3

Adjusting High-End Trim -

Save

To optimize performance of CFL / LED lamps

1

HOLD Enter

UNTIL

Status LED stops flashing HOLD

0

5 10

UNTIL

15

6 sec.

A status LED starts flashing

2

Adjust

a. HOLD Hold

UNTIL

Light is at full brightness

24

0301710b 07/2014

Wireless Adjusting Low-End Trim on a CasétaTM Wireless Plug-In Lamp Dimmer

On

2

Adjust (continued)

b.

TAP

Brighter Darker UNTIL Off Light stops flickering and is stable

Plug-in lamp dimmer

Adjusting Low-End Trim -

3

To optimize performance of CFL / LED lamps

Save HOLD

1

Enter UNTIL HOLD

UNTIL 0

5

The indicator LED stops flashing

10 15

6 sec.

The indicator LED starts flashing

4 a.

Verify a. Tap "Off" one time. Light will turn off. b. Tap "Brighter" one time. Light will turn on.

2

Adjust

a.

HOLD

c. If light is still off or is flickering, repeat steps 1-4. UNTIL

Hold

b.

Light stops dimming or turns off

25

0301710b 07/2014

Wireless Adjusting High-End Trim on a CasétaTM Wireless Plug-In Lamp Dimmer

On

2

Adjust (continued)

b.

TAP

Brighter Darker UNTIL Off Desired light level is achieved

Plug-in lamp dimmer

Adjusting High-End Trim To optimize performance of CFL / LED lamps

1

3

Save

Enter HOLD HOLD

UNTIL 0

5

UNTIL

10 15

6 sec.

The indicator LED stops flashing The indicator LED starts flashing

2 a.

Adjust

HOLD

UNTIL

Hold

Light is at full brightness

26

0301710b 07/2014

Wireless Converting a CasétaTM Wireless Plug-In Lamp Dimmer to a Switch to Control Non-Dim Loads

2

Verify

On a. Brighter

a. Tap "Off" one time. Light will turn off. b. Tap "On" one time. Light will turn on. – The "Brighter" and "Darker" buttons will be disabled and do nothing.

Darker

Off

Plug-in lamp dimmer b.

1

Press and Hold "On" and "Off" buttons

HOLD

Note: Only use lighting loads on your plug-in lamp dimmer, even when operating in switch mode.

UNTIL 0

5 10 15

6 sec.

The indicator light flashes

3

27

To change back to dimmer mode repeat step 1

0301710b 07/2014

Wireless Removing Paired Pico® Remote Controls from a Caséta Wireless Dimmer TM

1

3x

2

3

Tap the "On" button quickly three times, holding on the last press TAP TAP

3x

Release the button, then immediately tap the button three more times TAP TAP

3x

Continue to hold the "On" button until the light begins to flash quickly

3x

3x

HOLD

Light will flash slowly three times, then turn off

4 0

All paired Pico ® remote controls are removed and all settings are returned to factory default

5 10

– After the device resets, the light will turn on to the full on state.

15

3 sec.

Note: This procedure also resets the high-end and low-end trim settings for CasétaTM Wireless dimmers.

HOLD UNTIL

Light starts flashing quickly

28